Sherwood RD-7503 manual Room 2 Source Playback, Press the Room 2 button to enter the Room 2 mode

Page 38

RD-7503(A)2008.11.41:45PM페이지38

ENGLISH

ROOM 2 SOURCE PLAYBACK

• This function allows enjoying one source in the main room and playing another in a different room at the same time.

Notes:

The analog signals from the EXTERNAL INs and the digital signals cannot be output to the different room, meaning no playback in a different room.

Only the (composite) video signals can be output to the different room.

1. Press the ROOM 2 button to enter the ROOM 2 mode.

ROOM 2 ~ is displayed for several seconds.

When the ROOM 2 setting mode disappears, press the ROOM 2 button again.

2. Select the desired mode while displaying the ROOM 2 setting mode.

Each time these buttons are pressed, the mode changes as follows :

ROOM 2 ~ : To turn on or off the ROOM 2 function.

(ROOM 2 mode)

IN ~ : To select the desired ROOM 2 source.

(ROOM 2 input)

VOL ~ : To adjust the volume on the power (ROOM 2 volume) amplifier assigned to "BACK← →ROOM

2" or "ROOM 2".

Note :

When the ROOM 2 mode is set to OFF, the ROOM 2 input and the ROOM 2 volume cannot be selected.

Notes:

3. Set the selected mode as desired.

When selecting the ROOM 2 mode.

ON : To turn on the ROOM 2 function.

("R2" lights up.)

OFF : To turn it off. ("R2" goes off.)

You can also set the ROOM 2 mode to ON or OFF with pressing the ROOM 2 button on the remote control.

When selecting the ROOM 2 input.

You can select the desired among MAIN source, TUNER, CD, F.AUX, TAPE, BT(Bluetooth IN), VIDEO 1 ~ VIDEO 3 as a ROOM 2 source.

When selecting the ROOM 2 volume.

You can adjust the volume on the power amplifier assigned to "BACK← →ROOM 2" or "ROOM 2" when the ROOM 2 speaker terminals are connected to the speakers in a different room. (For details, refer to "When selecting the AMP ASSIGN" on page 41.)

4. Start play on the component related to the ROOM 2 source.

When the EXTERNAL IN is selected as a main input, if the MAIN source is selected as a ROOM 2 input, no audio signal can be heard in the different room (ROOM 2).

Even when this receiver enters the standby mode, in such a case that "R2" lights up still and the STANDBY indicator lights up blue as it does in the operating mode, meaning only the ROOM 2 circuitry operates, the ROOM 2 source can be played independently.

When you do not use the ROOM 2 function, turn off the ROOM 2 function to save electricity.

38

Image 38
Contents RD-7503 Important Safety Instructions 120 IntroductionRead this Before Operating Your Unit Contents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1 Connecting Audio ComponentsComponent video input default settings *2 Copyright protection systemDigital input default settings Connecting External INSConnecting Digital INS and OUT Front Bi-Amp Connections Connecting SpeakersSurround back speakers Speaker placement Connecting Subwoofer PRE OUTConnecting Room 2 Outs Connecting DC Trigger OUTAC Input Cord Connecting for System ControlConnecting Sirius Connector only for North America SiriusConnect Home TunerFluorescent Display Front Panel ControlsRemote Sensor Front AUX in Jack Setup MIC JackBluetooth in Connector UP/DOWN / buttons Numeric 0~9, +10 Input Selector buttons Universal Remote ControlsPower on button ENTER/SEARCH MODE, Select buttonsFunction Table of the Numbered Buttons Loading Batteries Entering a setup code Repeat the above steps 1 to 4 for each of your ComponentsRemoving all punch-through functions Using a punch-through functionRemoving a punch-through function To remove a macro program Programming a macro functionOperating a macro function To change a macro programBefore operation OperationsListening to a Program Source Muting the sound When CD, F.AUX, Video 1~ 3 is selected as an input sourceListening with headphones Surround modes Stadium TheaterHall RoomEnjoying Surround Sound Dolby TruehdCancel the test tone function Adjusting each channel level with test toneEnter the test tone mode To cancel the surround mode for stereo operationRepeat the above steps 2 and 3 to adjust each channel level Adjusting the current channel levelAdjust the level of the selected channel as desired Press the Channel Level buttonMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsTuning Manual presettingTuning to preset stations Press the MEMORY/ENTER buttonSirius Satellite Radio only for North America Press the Tuning UP+/DOWN- buttons repeatedly to select SRTo sign up, access the website at Signing up for Sirius Satellite Radio→ DIR Srch → CAT Srch → OFF Direct searchCategory search Presetting channels Preset searchTune in the channel you want to lock or unlock When tuning in the previously locked channelsParental lock Recording Dubbing the audio and video signals separately onto VideoTo record audio signals Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent display Displaying the operation statusRoom 2 Source Playback Press the Room 2 button to enter the Room 2 modeSet the selected mode as desired Start play on the component related to the Room 2 sourceTurn the menu screen on OSD Menu SettingsSelect the desired menu using the Cursor UP/DOWN buttons When selecting the CH Level Setup When selecting the SPEAKER/ROOMEQSETUPWhen selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust Press the Cursor UP/DOWN buttons to select the desired itemWhen selecting the Tone Control When selecting the Subwoofer ModeWhen selecting the Hdmi Audio OUT When selecting the Cinema EQ When selecting the Momentary OSDWhen selecting the OSD Position Adjust Setting the Input Setup When selecting the menu of page 2 orWhen selecting the Audio Assign When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Audio ModeWhen selecting the DC Trigger When selecting the Auto SurroundWhen selecting the AV Sync When selecting the HD AudioTo resume its factory input source name When selecting the NameConfirm your entry When selecting the Parental Lock When selecting the Edit Lock Code Preparations Setting the Speaker / Room EQ SetupWhen selecting the Auto Setup RD-7503A2008.11.4145PM페이지52 When selecting the Speaker Configuration When selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Repeat the above steps 1 and 2 to adjust each channel level Setting the CH Level SetupMemory mode Reference Auto Setting the Sound ParameterWhen selecting the Night Mode When selecting the Panorama mode When selecting the Dolby Plii MusicRepeat the above steps 2 and 3 to adjust other parameters When selecting the Center Width controlWhen selecting the Input Setting the Multi Room SetupWhen selecting the Room When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Setup Code Table TMK RCASSS CCESTS KLHMEI ABC NSCSAT HTSRD-7503