Installation Instructions
3ELECTRICAL CONNECTIONS (CONT.)
BUsage Situations where Appliance Power Cord will be Disconnected Frequently.
Do not use an adapter plug in these situations because disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the adapter ground terminal. The customer should have the
The installation of appliances designed for mobile home installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or, when such standard is not applicable, the Standard for Manufactured Home Installations, latest edition (Manufactured Home Sites, Communities and
Electric Disconnect
•Locate disconnect plug on the range back.
•Pinch sides of connector and pull out of range back.
4SEAL THE OPENINGS
Seal any openings in the wall behind the range and in the floor under the range when hookups are completed.
5ASSEMBLE SURFACE BURNERS
CAUTION: Do not operate the burner without all burner parts in place.
AAssemble the side burners as shown.
Side
Grate
Burner cap 
Burner head 
Electrode 
5ASSEMBLE SURFACE BURNERS (CONT.)
BAssemble the center burner. Make sure that the locking feet on the center grate hook over the side grates.
Center Grate
Locking
Foot 
Burner head | Locking |
and cap | Foot |
assembly | Electrode |
|
CReplace the burner heads and caps. Make
sure that the heads and caps are replaced in the correct location. There is one oval (center) head and cap assembly and four side heads and caps.
For model JGBS80:
Medium burner Oval head and cap | Small burner | ||||||||||||||||||||||||||||
head and cap |
|
|
|
|
|
|
|
| assembly | head and cap | |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Front of range |
|
| |
Large burner | Extra large | |||
| ||||
head and cap |
| burner head | ||
|
| and cap | ||
For model JGBS09:
Medium burner Oval head and cap | Medium burner | |||||
head and cap | assembly | head and cap | ||||
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Front of range |
|
|
|
| ||
Medium burner | Medium |
| burner |
head and cap | head and cap | ||
Make sure the slot in the burner head is positioned over the electrode.
Slot
Slot
Electrode 
Make sure that the heads and caps are replaced in the correct locations.
35