ELAN Home Systems U102110-07 manual Servicing Notes

Page 33

SERVICING - WARNING

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

Servicing Notes

When servicing or replacing gas carrying components disconnect from gas before commencing operation and check appliance is gas sound after completion. When checking for gas leaks use a liquid leak detector at all joints and connections to check for leaks in the system. Use a product specifically manufactured for leak detection. Leak testing of the appliance shall be conducted in accordance to the manufacturer’s instructions.

CAUTION: DO NOT USE A FLAME TO CHECK FOR GAS LEAKS.

Do not use re-conditioned or unauthorised gas controls.

Disconnect from electricity supply before commencing servicing, particularly before removing any of the following: control panel, side panels, cooktop tray, or any of the electrical components or cover boxes. Before electrical reconnection check that the appliance is electrically safe.

1. To Remove the Hand Rail

Remove the handrail plastic blanking plugs and remove the 2 end bracket fixing screws.

2. To Remove Control Panel

Disconnect from electricity supply.

Pull off all the control knobs. Remove the hand rail (see 2) Remove the 2 cross headed screws that were hidden by the hand rail end brackets.

Open the grill door and R H oven door and remove the 2 screws underneath the control panel.

Pull the control panel forward and support so that the wires are not strained.

Reassemble in reverse order. When replacing leads refer to the wiring diagram. Check operation of timer, ignition, and oven light switches.

3. To Remove the Hotplate top

Disconnect from electricity supply.

Remove the pan supports, cooktop burner caps and tops. If there are screws holding the cooktop burners to the cooktop, remove them (not the spark electrode fixing screws).

ACooktop front fixing screws

BCooktop rear fixing screws

Remove the 2 rear cooktop fixing screws (B) and the 4 front cooktop fixing screws (A).

Remove the screws holding the flue grille stays.

Lift the cooktop clear of the appliance. Replace in reverse order.

Reassemble in reverse order ensuring that the leads are reconnected.

Check for correct burner operation.

4. To Remove a Side Panel

Disconnect from electricity supply.

Remove control panel (see 2). Pull the cooker forward. Remove the 4 retaining screws for each panel (2 at the front and 2 at the rear). The lower front retaining screws (one each side) are situated beneath the lower edge at the front corners of the side panels

Reassemble in reverse order.

5. To Remove Oven Light Switch

Remove control panel (see 2).

NB The old switch may be destroyed during removal.

Remove switch button and old switch from its bezel by gripping the switch body behind the control panel and twisting sharply.

The switch bezel can then be removed by folding back its locking wings and pushing forward. Fit the new bezel to the control panel by first lining up the raised key on its body with the cutout in the control panel and pushing it in from the front. Assemble the new switch to the bezel by lining up the key sections and pushing home. Fit the new button by pushing in from the front.

Replace control panel in reverse order and test for correct operation.

6. To Remove Electronic Timer

Disconnect from electricity supply.

Pull off the timer control buttons and remove the control panel (See 2). Remove the timer/mounting bracket assembly from the control panel by removing the two fixing screws. Remove the timer from its mounting bracket by depressing the plastic lugs on the timer case, at the same time pulling the unit forward.

Reassemble in reverse order. When replacing leads refer to the wiring diagram. Check operation of timer.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Dual Fuel Users Guide Be safe Gas and Electricity onPeculiar smells Contents Hotplate Burners Griddle High/mediumMedium/low Care and Cleaning Wok cradleEssential information Grill Left Hand Oven Right Hand Oven OvensClock Clock Special Features Auto is showing, you want to reset to manual cookingTo activate the key lock To turn off the key lockBoth Ovens Cooking using the timerMulti-function oven functions Multi-function ovenConventional oven top and base heat HandyrackOven shelves SteamOven light Storage To remove the drawer pull it fully forwardTo refit the draw Cooking chart Fan assisted oven function Multi-function Oven cooking guideEnsure meat and poultry is fully cooked before serving Fish Oven Cooking chart Conventional and full Fan oven functionsHotplate burners Cleaning your cookerCentral hotplate Wok burnersGrill GriddleControl Panel and Doors OvensHotplate Part Finish Recommended Cleaning Method Cleaning TableMoving your cooker Troubleshooting Turn off the power supply Oven temperature getting hotter as the cooker gets olderGrill not cooking properly Oven light is not workingGeneral Safety Instructions If you smell gas0800 111 This appliance is heavy, take care when moving it Dear Installer InstallationProvision of Ventilation Location of CookerYou will also need the following tools ConversionChecking the parts Electric drill Masonry drill bitPositioning the Cooker Unpacking the CookerMoving the Cooker Levelling Fit the HandlesHandles should be above the fixings Fitting the splash back Pressure testingFitting a stability bracket Gas ConnectionHotplate Electrical ConnectionOven check Fitting the plinthConversion to LP gas Tap adjustmentJets Stick on labelServicing Notes To Change Grill Controller To Remove a ThermostatTo Change a Hotplate Tap To Change a Hotpate burner jetTo Change Oven Door Outer Panel To Adjust Oven Door Catch KeepTo Change Oven Door Catch To Change Oven Door SealTo Remove the LH Oven Bottom and Top Elements To Remove Oven Inner BackTo Replace an Oven Fan To Remove an Oven fan ElementCircuit Diagram Dimensions Technical DataThis cooker is category II2H3+ ConnectionsRatings
Top Page Image Contents