ELAN Home Systems U102110-07 Electrical Connection, Hotplate, Oven check, Fitting the plinth

Page 31

Electrical Connection

This appliance must be installed by a qualified electrician to comply with the relevant Institute of Electrical Engineers (I.E.E.) regulations and also the local electricity supply company requirements.

WARNING: THIS APPLIANCE MUST BE EARTHED

Note

The cooker must be connected to the correct electrical supply as stated on the voltage label on the cooker, through a suitable cooker control unit incorporating a double pole switch having a contact separation of at least 3mm in all poles. This cooker must not be connected to an ordinary domestic power point.

The cable size used should be between 6mm2 and 10mm2, twin and earth.

Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel. Connect the mains cable to the correct terminals for your electrical supply type (see fig.). Check that the links are correctly fitted and that the terminal screws are tight. Secure the mains cable using the cable clamp.

These appliances are of type X with regard to protection against over heating of the surrounding surfaces.

Current Operated Earth Leakage Breakers

Where the installation is protected by a 30 milliamp sensitivity residual current device (RCD), the combined use of your cooker and other domestic appliances may occasionally cause nuisance tripping. In these instances the cooker circuit may need to be protected by fitting 100mA device. This work should be carried out by a qualified electrician.

Oven Light

Press the oven light switch and check that the light is working.

NB. The oven light bulb is not included in the guarantee

Hotplate

Check each burner in turn. Push in tap and turn to the large flame symbol. Press ignition switch on facia panel.

Grill

Open the grill compartment door. Turn on the grill control and check that the grill heats up.

Oven check

Set the clock to the time of day

When the clock is first connected the display will flash

(

) and (

) alternately.

To set the clock to read the time of day turn and hold the Timer knob to the clock symbol and at the same time turn the Adjusting knob left or right until the clock shows the time of day. Remember this is a 24 hour clock. Let go of the Timer knob and it will spring back to the vertical oven manual setting.

Turn on the oven and check that the oven fan starts to turn and that the oven starts to heat up. Turn off the oven.

Fitting the plinth

Loosen the 3 screws along the front bottom edge of the cooker. Hook the central keyhole over the central screw. Twist and fit each end keyhole over their respective screws. Tighten the fixing screws.

Customer care

Please complete your details in this Guide, inform the user how to operate the cooker and hand over the Instructions.

Thank you.

31

Image 31
Contents Dual Fuel Users Guide Gas and Electricity on Be safePeculiar smells Contents Hotplate Burners High/medium GriddleMedium/low Wok cradle Care and CleaningEssential information Grill Left Hand Oven Right Hand Oven OvensClock To turn off the key lock Auto is showing, you want to reset to manual cookingClock Special Features To activate the key lockBoth Ovens Cooking using the timerMulti-function oven functions Multi-function ovenConventional oven top and base heat HandyrackSteam Oven shelvesOven light To remove the drawer pull it fully forward StorageTo refit the draw Multi-function Oven cooking guide Cooking chart Fan assisted oven functionEnsure meat and poultry is fully cooked before serving Fish Oven Cooking chart Conventional and full Fan oven functionsWok burners Cleaning your cookerHotplate burners Central hotplateOvens GriddleGrill Control Panel and DoorsHotplate Part Finish Recommended Cleaning Method Cleaning TableMoving your cooker Troubleshooting Oven light is not working Oven temperature getting hotter as the cooker gets olderTurn off the power supply Grill not cooking properlyIf you smell gas General Safety Instructions0800 111 This appliance is heavy, take care when moving it Location of Cooker InstallationDear Installer Provision of VentilationElectric drill Masonry drill bit ConversionYou will also need the following tools Checking the partsUnpacking the Cooker Positioning the CookerMoving the Cooker Fit the Handles LevellingHandles should be above the fixings Gas Connection Pressure testingFitting the splash back Fitting a stability bracketFitting the plinth Electrical ConnectionHotplate Oven checkStick on label Tap adjustmentConversion to LP gas JetsServicing Notes To Change a Hotpate burner jet To Remove a ThermostatTo Change Grill Controller To Change a Hotplate TapTo Change Oven Door Seal To Adjust Oven Door Catch KeepTo Change Oven Door Outer Panel To Change Oven Door CatchTo Remove an Oven fan Element To Remove Oven Inner BackTo Remove the LH Oven Bottom and Top Elements To Replace an Oven FanCircuit Diagram Connections Technical DataDimensions This cooker is category II2H3+Ratings