ELAN Home Systems U102110-07 Levelling, Fit the Handles, Handles should be above the fixings

Page 29

Fit the levelling tool on the rectangular adjuster as shown below.

LOWER THE FRONT ROLLER by doing 14 complete (360°) turns clockwise. (This means turning and removing the levelling tool 56 times).

Now LOWER THE TWO REAR ROLLERS.

First fit the levelling tool on the hexagonal adjusting nut as shown below.

Make 10 complete (360°) turns clockwise. (This means turning and removing the levelling tool 20 times).

Levelling

You are recommended to use a spirit level on a shelf in one of the ovens to check for level.

Place the cooker in its intended position taking care not to twist it within the gap between the kitchen units as damage may occur to the cooker or the units.

The rollers can be adjusted to level the cooker. To adjust the height of the rear of the cooker use the levelling tool supplied to turn the adjusting nuts at the front bottom corners of the cooker.

Adjust the height of the front roller to level the cooker. Turn clockwise to raise the cooker and anticlockwise to lower.

When you are satisfied with the height and level raise the front of the cooker by one turn of the front roller adjuster. Screw down the front feet to meet the floor. Screw the front roller adjuster anticlockwise to raise the front roller so that the front of the cooker is supported on the feet, not the front roller, to prevent accidental movement of the cooker.

Leave the levelling tool in the storage drawer, so that the customer can use it if they wish to move the cooker.

To refit the draw pull out the side runners. Rest the drawer back on the side runners and, keeping it level, push it right back. The clips should click into position holding the drawer to the side runners. Replace the drawer by locating on side runners and push in.

Make sure you lower BOTH REAR ROLLERS. There are two adjusting nuts, one for each roller, at both the front bottom corners of the cooker.

Unfold the rear edge of pack base tray. Carefully push the cooker backwards along the hardboard strips and into position. Take care not to damage the power cable. Push the cooker close to its final position, leaving just enough space to get behind it.

Fit the Handles

Remove the 4mm Allen screws from the doors with the hexagon key tool. Use the screws to fit the door handles.

The handles should be above the fixings.

Fit the plastic blanking plugs to the fixing holes.

Remove the 4mm Allen screws from the top corners of the fascia and fix the front handrail in position.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Dual Fuel Users Guide Peculiar smells Be safeGas and Electricity on Contents Hotplate Burners Medium/low GriddleHigh/medium Essential information Care and CleaningWok cradle Grill Left Hand Oven Right Hand Oven OvensClock Clock Special Features Auto is showing, you want to reset to manual cookingTo activate the key lock To turn off the key lockBoth Ovens Cooking using the timerMulti-function oven functions Multi-function ovenConventional oven top and base heat HandyrackOven light Oven shelvesSteam To refit the draw StorageTo remove the drawer pull it fully forward Ensure meat and poultry is fully cooked before serving Cooking chart Fan assisted oven functionMulti-function Oven cooking guide Fish Oven Cooking chart Conventional and full Fan oven functionsHotplate burners Cleaning your cookerCentral hotplate Wok burnersGrill GriddleControl Panel and Doors OvensHotplate Part Finish Recommended Cleaning Method Cleaning TableMoving your cooker Troubleshooting Turn off the power supply Oven temperature getting hotter as the cooker gets olderGrill not cooking properly Oven light is not working0800 111 General Safety InstructionsIf you smell gas This appliance is heavy, take care when moving it Dear Installer InstallationProvision of Ventilation Location of CookerYou will also need the following tools ConversionChecking the parts Electric drill Masonry drill bitMoving the Cooker Positioning the CookerUnpacking the Cooker Handles should be above the fixings LevellingFit the Handles Fitting the splash back Pressure testingFitting a stability bracket Gas ConnectionHotplate Electrical ConnectionOven check Fitting the plinthConversion to LP gas Tap adjustmentJets Stick on labelServicing Notes To Change Grill Controller To Remove a ThermostatTo Change a Hotplate Tap To Change a Hotpate burner jetTo Change Oven Door Outer Panel To Adjust Oven Door Catch KeepTo Change Oven Door Catch To Change Oven Door SealTo Remove the LH Oven Bottom and Top Elements To Remove Oven Inner BackTo Replace an Oven Fan To Remove an Oven fan ElementCircuit Diagram Dimensions Technical DataThis cooker is category II2H3+ ConnectionsRatings
Top Page Image Contents