Woods Equipment BW15LH manual Storage

Page 10

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

(Safety Rules continued from previous page)

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

Make certain all movement of equipment com- ponents has stopped before approaching for ser- vice.

Frequently check blades. They should be sharp, free of nicks and cracks, and securely fastened.

Do not handle blades with bare hands. Careless or improper handling may result in serious injury.

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service.

Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

Make sure shields and guards are properly installed and in good condition. Replace if damaged.

Never perform service or maintenance with engine running.

Do not disconnect hydraulic lines until machine is securely blocked or placed in lowest position and system pressure is released by operating valve levers.

Service and maintenance work not covered in OWNER SERVICE must be done by a qualified dealership. Special skills, tools, and safety proce- dures may be required. Failure to follow these instructions can result in serious injury or death.

Explosive separation of tire and rim parts can cause serious injury or death. Release all air pres- sure before loosening bolts on wheel.

STORAGE

Before disconnecting and storing, follow these instructions:

Store on level, solid ground.

Disconnect driveline and secure up off the ground.

Lower wings to ground.

Raise cutter center section and pin transport bar in raised position.

Attach parking jack and raise tongue weight off tractor drawbar.

Place wedge blocks at front and rear of wheels on center section and each wing to pre- vent wheel rotation.

Securely block all four corners of center sec- tion and each wing with jackstands.

Remove hydraulic hoses after tractor is turned off and all system pressure is released by operating valve levers several times.

Remove safety tow chain.

Remove retainer pin and high strength draw- bar pin.

Keep children and bystanders away from stor- age area.

10Safety

BW180LH_SR (10/15/2009)

Image 10
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesInstallation PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be CarefulKeep Away Safety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionCV Driveline Turning Limits Cutting Height AdjustmentInterference Check Tractor OperationMowing Tips Cutter OperationShredding Transporting Lock-UpPRE-OPERATION Check List Owners ResponsibilityOwner Service Owner ServiceBlocking Method Driveline Lubrication LubricationGearbox Lubrication Blades Blade Installation FigureSeasonal Lubrication Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningShielding Repair CleaningServicing Tires Safely Troubleshooting TroubleshootingGearbox Maintenance Dealer ServiceDealer Service Seal Replacement FigureSpindle Gearbox Repair Remove Gearbox from Cutter Vertical Shaft Seal Repair Spindle BOXHorizontal Shaft Seal Repair Disassemble GearboxSpindle Gearbox Assembly Reinstall Gearbox Assemble GearboxAssembly DisassemblySplitter Gearbox Repair Figure Removal from Cutter Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalJoint Disassembly Crossbar InstallationUniversal Joint Repair Joint Assembly Assembly Instructions AssemblyDealer SET-UP Instructions Install Height Adjustment Cylinder Install SMV EmblemInstall Wheel and Hub Install TongueInstall Wing Install CV DriveInstall Wing Cylinder & Lock-up Bar Install Wing Wheel and Hub Figure Left Wing Lock-Up Bar InstalledInstall Wing Driveline Install Wing Wheel Yoke Adjustment LinkInstall Hose Kit Install Chain or Belt Shielding Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListMAN0810 9/24/2009 Parts BW15LHMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid Wing Drive Assembly Bodioli and Pavesi NSSBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITWinch KIT Optional Winch Kit InstallationWinch Kit Operation Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty