Woods Equipment BW15LH manual Install Wing Wheel and Hub Figure, Left Wing Lock-Up Bar Installed

Page 38

2.Slide spacer (38) and lock-up bar (13) over clevis pin (33) on back side of cylinder lug & secure with 1"x1-7/8" washers (53) and cotter pins (80).

3.Attach base end of wing cylinder (4) to cylinder links (11 & 12) and washers (52) using clevis pin

(32)and cotter pins (80).

4.Remove plug from base end of hydraulic cylinder. Align cylinder rod end with cylinder lug on the wing and insert lock-up pin (35).

5.Slide spacer (37) over lock-up pin (35) on back side of cylinder rod and secure with cotter pins

(80).

6.Insert safety pin (83) into the end of lock-up pin

(35). The safety pin will secure lock-up bar into position when wing is in the UP position.

7.Extend cylinder fully & replace plug in base end of cylinder. This trapped air will help push wing down.

8.Install bushing (40), elbow, (41) and hose (43) to the rod end of cylinder (4). See Install Hose Kit, page 39 for complete instructions.

9.Repeat procedure for opposite wing.

11

12

13

 

 

 

33

 

 

 

80

 

38

 

 

 

 

 

DP3

 

 

 

 

11.

Cylinder link

38.

Spacer, 1"

12.

Cylinder link

80.

Cotter pin,

13.

Wing lock-up bar

 

1/4" x 1-1/2"

33.Headless pin, 1" x 4.08"

Figure 29. Left Wing Lock-Up Bar Installed

Install Wing Wheel and Hub (Figure 30)

1.Insert wheel hub into wing wheel yoke arms (5) and align holes.

2.Secure into position using cap screw (64) and flanged lock nut (68).

3.Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside for steel rim for pneumatic tires and rims. Tighten to 75 lbs-ft. Check that tire air pressure is a maximum of 40 psi.

NOTE: Install the flat side of the nut toward the inside for solid tires and aircraft tires (shown).

4.Install optional dual wheel and hub to inside of wheel yoke arm.

5.Wing wheel yoke arm, right

29. Wheel and hub

64.1/2 NC x 3 HHCS GR5

68.1/2 NC Flanged lock nut

Figure 30. Wing Wheel and Hub Installation - Right

38 Assembly

MAN0810 (9/24/2009)

 

 

Image 38
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesInstallation PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be CarefulKeep Away Safety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionCV Driveline Turning Limits Cutting Height AdjustmentInterference Check Tractor OperationShredding Cutter OperationMowing Tips Transporting Lock-UpPRE-OPERATION Check List Owners ResponsibilityBlocking Method Owner ServiceOwner Service Gearbox Lubrication LubricationDriveline Lubrication Blades Blade Installation FigureSeasonal Lubrication Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingGearbox Maintenance Dealer ServiceDealer Service Seal Replacement FigureSpindle Gearbox Repair Remove Gearbox from Cutter Vertical Shaft Seal Repair Spindle BOXHorizontal Shaft Seal Repair Disassemble GearboxSpindle Gearbox Assembly Reinstall Gearbox Assemble GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install Height Adjustment Cylinder Install SMV EmblemInstall Wheel and Hub Install TongueInstall Wing Cylinder & Lock-up Bar Install CV DriveInstall Wing Install Wing Wheel and Hub Figure Left Wing Lock-Up Bar InstalledInstall Hose Kit Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Install Chain or Belt Shielding Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListMAN0810 9/24/2009 Parts BW15LHMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid Wing Drive Assembly Bodioli and Pavesi NSSBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITWinch Kit Operation Winch Kit InstallationWinch KIT Optional Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty