Woods Equipment BW15LH manual Install Wing Wheel Yoke Adjustment Link, Install Wing Driveline

Page 39

Install Wing Wheel Yoke Adjustment Link

CAUTION

Use a suitable lifting device of sufficient capac- ity. Use adequate personnel to handle heavy com- ponents.

1.With a lifting device raise right wing and lock in the up position using the wing lock-up bar. Leave lifting device attached for added support.

2.Attach adjustable link (30) to right side of center wheel yoke arm and secure with cap screw (51) and lock nut (55).

3.Attach opposite end of adjustable link (30) to wing wheel yoke arm and secure with cap screw (51) and lock nut (55).

4.Remove lock-up bar and carefully lower wing using lifting device.

5.Repeat process for left wing.

30

51

55

DP2

30. Adjustable link

51. 1 NC x 4-1/2 HHCS GR5

55. 1 NC Lock nut

Figure 31. Left Wing Wheel Yoke

Adjustment Link Installed

Install Wing Driveline

1.Attach clutch shield (8) to wing gearbox using four cap screws (84), lock washers (75), and flat washers (74).

2.Slide non clutch end of driveline (3) over wing gearbox shaft. Make sure the lock collar engages securely.

3.Slide clutch end of driveline over splitter gearbox and secure using cap screws and lock nuts supplied with driveline.

4.Repeat process for left driveline.

3.Wing driveline, complete

18.Clutch shield

74.5/16" Flat washer

75.5/16" Lock washer

84.M8 x 1.25P x 20 mm HHCS

Figure 32. Right Driveline Installation

Install Hose Kit

1.Remove plug from rod end of each wing cylinder.

2.With the wings in the down position and cylinder extended, remove and reinstall the plugs from the base of the wing cylinders. This will trap air behind the piston and help when lowering the wings.

3.Install reducer bushing and restricter elbow into cylinders. Position elbow on center cylinder to point forward; on wing cylinders point elbows to the center.

NOTE: Make sure a breather fitting is installed in the rod end port of the wheel yoke cylinder.

4.Attach hose to each elbow.

MAN0810 (9/24/2009)

Assembly 39

 

 

Image 39
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesInstallation TrainingOperation TransportationMaintenance Storage Be Careful Safety & Instructional DecalsKeep Away Safety Hydraulic Connection Connecting Cutter to TractorOperation OperationTractor Operation Cutting Height AdjustmentInterference Check CV Driveline Turning LimitsCutter Operation Mowing TipsShredding Lock-Up TransportingOwners Responsibility PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Lubrication Driveline LubricationGearbox Lubrication Blade Removal Figure Blade Installation FigureSeasonal Lubrication BladesBlade Sharpening Slip Clutch Adjustment FigureCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingSeal Replacement Figure Dealer ServiceDealer Service Gearbox MaintenanceDisassemble Gearbox Vertical Shaft Seal Repair Spindle BOXHorizontal Shaft Seal Repair Spindle Gearbox Repair Remove Gearbox from CutterSpindle Gearbox Assembly Assemble Gearbox Reinstall GearboxDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsDealer SET-UP Instructions Install SMV Emblem Install Height Adjustment CylinderInstall Tongue Install Wheel and HubInstall CV Drive Install WingInstall Wing Cylinder & Lock-up Bar Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Wing Wheel Yoke Adjustment Link Install Wing DrivelineInstall Hose Kit Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Delivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListMAN0810 9/24/2009 BW15LH PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid NSS Wing Drive Assembly Bodioli and PavesiBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalWinch Kit Installation Winch KIT OptionalWinch Kit Operation Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Warranty