Woods Equipment BW15LH manual Install CV Drive, Install Wing Cylinder & Lock-up Bar

Page 37

Install CV Drive

1.Align hole in drive yoke with groove on gearbox input shaft and slide rear half of drive (5) onto shaft.

2.Secure with bolt and nut supplied with drive.

5. CV Drive

Figure 26. CV Drive Installation

Install Wing

CAUTION

Use a suitable lifting device of sufficient capac- ity. Use adequate personnel to handle heavy com- ponents.

The wing must be installed in the following sequence and will require at least two people. A floor jack or a suitable lifting device will be helpful to align decks when installing the hinge pin.

1.Attach winglet (7) to wing using three carriage bolts (69) and flange lock nuts (70).

2.Remove hinge pin (11) from center section.

3.Place wing assembly adjacent to the center section and align hinge sections.

4.Insert hinge pin through the hinge sections and secure with spring pin (81) and washer (52) on both ends.

5.Attach side skid (6) to the wing using four carriage bolts (66) and flange lock nuts (68).

6.Repeat procedure of opposite wing.

6.

Skid Shoe

68.

1/2 NC Lock Nut

7.

Winglet

69.

3/8 NC x 1 Carriage

11.

Hinge Pin

 

Bolt

52.

1” Flat Washer

70.

3/8 NC Lock Nut

66.1/2 NC x 1 Carriage Bolt 81. 1/4 x 1-1/2 Spring Figure 27. Right Wing Installation

Install Wing Cylinder & Lock-up Bar

4.

Hydraulic cylinder

40.

1/2" x 1/4" Pipe

 

11.

Cylinder link

 

reducer bushing

12.

Cylinder Link

41.

1/4 " x 1/4" Elbow w/

13.

Wing lock-up bar

 

1/16" restricter

32.

1" x 2.72" Headless

43.

1/4" x 1/4" x 200"

 

pin

 

Hose

33.

1" x 4.08" Headless

52.

1" Flat washer

 

pin

53.

1" x 1-7/8" x 1/4"

35.

Lock-up pin 1" x 5"

 

Washer

37.

Spacer, 3/4

80.

1/4" x 1-1/2" Cotter

38.

Spacer, 1"

 

pin

83.

3/16" Safety pin

27.

Washer, 1 x 1-7/8

 

 

 

Figure 28. Wing Cylinder & Lock-Up Bar Installation

1.Place two cylinder links (11 & 12) on either side of cylinder lug on center section as shown, align holes and insert clevis pin (33).

NOTE: Items 11 & 12 must be installed with square corners on top and facing cylinder as shown.

MAN0810 (9/24/2009)

Assembly 37

 

 

Image 37
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishInstallation Safety RulesTraining PreparationOperation TransportationMaintenance Storage Be Careful Safety & Instructional DecalsKeep Away Safety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionInterference Check Cutting Height AdjustmentCV Driveline Turning Limits Tractor OperationMowing Tips Cutter OperationShredding Lock-Up TransportingOwners Responsibility PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Driveline Lubrication LubricationGearbox Lubrication Seasonal Lubrication Blade Installation FigureBlades Blade Removal FigureBlade Sharpening Slip Clutch Adjustment FigureShielding Repair CleaningServicing Tires Safely Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureHorizontal Shaft Seal Repair Vertical Shaft Seal Repair Spindle BOXSpindle Gearbox Repair Remove Gearbox from Cutter Disassemble GearboxSpindle Gearbox Assembly Assemble Gearbox Reinstall GearboxAssembly DisassemblySplitter Gearbox Repair Figure Removal from Cutter Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalJoint Disassembly Crossbar InstallationUniversal Joint Repair Joint Assembly Assembly Instructions AssemblyDealer SET-UP Instructions Install SMV Emblem Install Height Adjustment CylinderInstall Tongue Install Wheel and HubInstall Wing Install CV DriveInstall Wing Cylinder & Lock-up Bar Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Wing Driveline Install Wing Wheel Yoke Adjustment LinkInstall Hose Kit Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0810 9/24/2009 BW15LH PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid NSS Wing Drive Assembly Bodioli and PavesiBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalWinch KIT Optional Winch Kit InstallationWinch Kit Operation SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty