Woods Equipment BW15LH manual Operation, Connecting Cutter to Tractor, Hydraulic Connection

Page 14

OPERATION

The designed and tested safety of this machine depends on it being operated within the limitations as explained in this manual. Be familiar with and follow all safety rules in the manual, on the cutter and on the tractor.

The safe operation of this cutter is the responsibility of the operator, who must be properly trained. The opera- tor should be familiar with the equipment and all safety practices before starting operation. Read the safety information on page 7 through page 13.

Recommended tractor ground speed for most condi- tions is from 1 to 6 mph.

Always operate tractor PTO at 540 rpm.

Full chain or rubber shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or dam- age property.

If this machine is not equipped with full chain or rubber shielding, operation must be stopped when anyone comes within 300 feet (92 m).

This shielding is designed to reduce the risk of thrown objects. The mower deck and protec- tive devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Never allow children or untrained persons to operate equipment.

Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

CAUTION

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

CONNECTING CUTTER TO TRACTOR

NOTICE

For tractors with a 1-3/8" diameter PTO shaft, the horizontal distance from the end of the tractor PTO shaft to the center of drawbar pin should be 14" for 540 rpm cutter. This will minimize joint knock and damage to drive components.

Figure 1. Cutter to Tractor Connection

1.Attach cutter using a 1-1/2" clevis pin and clip.

2.Attach safety tow chain (32) to drawbar support. Leave enough slack for turning (Figure 1).

3.Connect cutter driveline to tractor PTO shaft, making sure the spring-activated lock pin slides freely and is seated in tractor PTO splined groove.

4.Remove parking jack (29) from the tongue and attach it to the storage post on the front of the left wing.

Hydraulic Connection

1.Inspect hydraulic hoses to ensure they are in good condition.

2.Clean the fittings before connecting them to the tractor hydraulic ports.

3.Route the hose through the hose holder at the hitch and be sure the hose can slide freely in the holder. Do not allow hose slack to drag on the ground or become caught on tractor protrusions.

4.Attach the hydraulic hose to the tractor.

5.From the operator position, start tractor and raise and lower deck several times to purge trapped air from the hydraulic cylinder.

14 Operation

MAN0810 (9/24/2009)

 

Image 14
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesInstallation PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be CarefulKeep Away Safety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionCV Driveline Turning Limits Cutting Height AdjustmentInterference Check Tractor OperationShredding Cutter OperationMowing Tips Transporting Lock-UpPRE-OPERATION Check List Owners ResponsibilityBlocking Method Owner ServiceOwner Service Gearbox Lubrication LubricationDriveline Lubrication Blades Blade Installation FigureSeasonal Lubrication Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingGearbox Maintenance Dealer ServiceDealer Service Seal Replacement FigureSpindle Gearbox Repair Remove Gearbox from Cutter Vertical Shaft Seal Repair Spindle BOXHorizontal Shaft Seal Repair Disassemble GearboxSpindle Gearbox Assembly Reinstall Gearbox Assemble GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install Height Adjustment Cylinder Install SMV EmblemInstall Wheel and Hub Install TongueInstall Wing Cylinder & Lock-up Bar Install CV DriveInstall Wing Install Wing Wheel and Hub Figure Left Wing Lock-Up Bar InstalledInstall Hose Kit Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Install Chain or Belt Shielding Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListMAN0810 9/24/2009 Parts BW15LHMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid Wing Drive Assembly Bodioli and Pavesi NSSBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITWinch Kit Operation Winch Kit InstallationWinch KIT Optional Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty