Woods Equipment BW15LH manual Transporting, Lock-Up

Page 17

TRANSPORTING

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Always raise unit and install transport locks before transporting. Leak down or failure of mechanical or hydraulic system can cause equip- ment to drop.

Always attach safety chain to tractor drawbar when transporting unit.

Never exceed 20 mph (32.2 km/h) during trans- port.

Never allow riders on power unit or attachment.

Do not operate PTO during transport.

Do not operate or transport on steep slopes.

Do not operate or transport equipment while under the influence of alcohol or drugs.

CAUTION

Always comply with all state and local lighting and marking requirements.

Lock-Up

Always transport with wings and center frame in the raised, locked position.

Wing Lock-Up

1.Raise wing to the up position.

2.Remove safety pin and lock-up bar from storage position.

3.Place lock-up bar over cylinder pin and secure with safety pin.

4.Repeat steps 1 to 3 for opposite wing.

5.Lower cylinder against lock-up bars (Figure 2).

DP4a

Figure 2. Transport Lock-Up Bar - Right Wing

Center Section Lock-Up

1.Raise cutter with hydraulic cylinder to maximum height.

2.Rotate transport lock into position over cylinder rod (Figure 3).

DP7

Figure 3. Transport Lock In Transport Position

3.Lower cutter against transport lock.

4.To lower cutter for operation, extend hydraulic cylinder to raise cutter. Rotate transport lock back away from cylinder rod (Figure 4).

5.Lower cutter to desired cutting height.

Figure 4. Transport Lock In Operation Position

MAN0810 (9/24/2009)

Operation 17

 

 

 

Image 17
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishInstallation Safety RulesTraining PreparationOperation TransportationMaintenance Storage Be Careful Safety & Instructional DecalsKeep Away Safety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionInterference Check Cutting Height AdjustmentCV Driveline Turning Limits Tractor OperationShredding Cutter OperationMowing Tips Lock-Up TransportingOwners Responsibility PRE-OPERATION Check ListBlocking Method Owner ServiceOwner Service Gearbox Lubrication LubricationDriveline Lubrication Seasonal Lubrication Blade Installation FigureBlades Blade Removal FigureBlade Sharpening Slip Clutch Adjustment FigureServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureHorizontal Shaft Seal Repair Vertical Shaft Seal Repair Spindle BOXSpindle Gearbox Repair Remove Gearbox from Cutter Disassemble GearboxSpindle Gearbox Assembly Assemble Gearbox Reinstall GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install SMV Emblem Install Height Adjustment CylinderInstall Tongue Install Wheel and HubInstall Wing Cylinder & Lock-up Bar Install CV DriveInstall Wing Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Hose Kit Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0810 9/24/2009 BW15LH PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid NSS Wing Drive Assembly Bodioli and PavesiBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalWinch Kit Operation Winch Kit InstallationWinch KIT Optional SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty