Woods Equipment BW15LH manual Seasonal Lubrication, Blades, Blade Installation Figure

Page 21

Seasonal Lubrication

In addition to the daily recommended lubrication, a more extensive application is recommended season- ally.

1.Fill CV double yokes with 20 pumps of grease with the joints in a straight line.

2.Articulate CV body to maximum angle several times to ensure full coverage of joints.

3.Place joints in the straight position and a add 10 additional pumps of grease to both joints.

4.Wipe telescoping drive clean of all old grease and contaminants.

5.Add a thin layer of new grease over telescoping drive.

BLADES

3.Align crossbar (10) with blade access hole in the cutter frame. Remove nut and lock washer. Carefully drive blade pin (9) out of crossbar.

4.Rotate crossbar and repeat for opposite blade.

NOTICE

If blade pin (9) is seized in crossbar and extreme force will be needed to remove it, support crossbar from below to prevent gearbox damage.

Blade Installation (Figure 6)

CAUTION

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

NOTICE

Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from drop- ping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Blade Removal (Figure 6)

1. Blade kit, CCW

9.Blade pin

10.Crossbar Assembly

36.Stump Jumper Pan

85.Blade lock clip

86.1/2 NC x 1-1/4 HHCS GR5

Figure 6. Blade Assembly

1.Disconnect driveline from tractor PTO.

2.Raise cutter and block securely (see Figure 5).

Crossbar rotation has clockwise rotation on left gearbox and counterclockwise rotation on the right and center gearboxes when looking down on cut- ter. Be sure to install blade cutting edge to lead in correct rotation.

NOTE: Always replace or sharpen both blades at the same time.

1.Inspect blade pin (9) for nicks or gouges, and if you find any replace the blade pin.

2.Insert blade pin through the blade. Blade should swivel on blade pin; if it doesn’t, determine the cause and correct.

3.Align crossbar (10) with blade access hole in cutter frame. Apply a liberal coating of Never-Seez® or equivalent to blade pin and crossbar hole. Make sure blade offset is down away from cutter.

4.Insert blade pin (9) through blade and align key on blade pin with keyway in crossbar and stump jumper pan. Push blade pin through crossbar.

5.Insert lock washer and nut through blade access hole in cutter frame. Install on blade pin (9) and tighten to 450 lbs-ft.

6.Repeat steps for opposite side.

NOTE: Blade should be snug but should swivel on pin without having to exert excessive force.

(Rev. 3/3/2010)

MAN0810 (9/24/2009)

Owner Service 21

Image 21
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishInstallation Safety RulesTraining PreparationOperation TransportationMaintenance Storage Be Careful Safety & Instructional DecalsKeep Away Safety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionInterference Check Cutting Height AdjustmentCV Driveline Turning Limits Tractor OperationCutter Operation Mowing TipsShredding Lock-Up TransportingOwners Responsibility PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Lubrication Driveline LubricationGearbox Lubrication Seasonal Lubrication Blade Installation FigureBlades Blade Removal FigureBlade Sharpening Slip Clutch Adjustment FigureCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureHorizontal Shaft Seal Repair Vertical Shaft Seal Repair Spindle BOXSpindle Gearbox Repair Remove Gearbox from Cutter Disassemble GearboxSpindle Gearbox Assembly Assemble Gearbox Reinstall GearboxDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsDealer SET-UP Instructions Install SMV Emblem Install Height Adjustment CylinderInstall Tongue Install Wheel and HubInstall CV Drive Install WingInstall Wing Cylinder & Lock-up Bar Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Wing Wheel Yoke Adjustment Link Install Wing DrivelineInstall Hose Kit Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0810 9/24/2009 BW15LH PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid NSS Wing Drive Assembly Bodioli and PavesiBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalWinch Kit Installation Winch KIT OptionalWinch Kit Operation SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty