Woods Equipment BW15LH manual Driveline Lubrication, Gearbox Lubrication

Page 20

1.

Driveline U-joint

10 Hours

6.

Tongue Pivot

40 Hours

2.

Telescoping shaft

10 Hours

7.

Wheel yoke pivot

40 Hours

3.

CV body assembly

40 hours

8.

Tailwheel spindle

20 Hours

 

(10 pumps minimum)

 

9.

Turnbuckle

40 Hours

4.

Driveline shield

10 Hours

 

 

 

5.

Gearbox (Check oil level) Daily

 

 

 

 

 

 

 

 

 

Figure 5. Jackstand Placement and Lubrication Points

LUBRICATION

Do not let excess grease collect on or around parts, particularly when operating in sandy areas.

See Figure 5 for lubrication points and frequency or lubrication based on normal operating conditions. Severe or unusual conditions may require more fre- quent lubrication.

Use a lithium grease of #2 consistency with a MOLY (molybdenum disulfide) additive for all locations unless otherwise noted. Be sure to clean fittings thoroughly before attaching grease gun. One good pump of most guns is sufficient when the lubrication schedule is fol- lowed.

4 or –5 in gearboxes. Fill gearbox until oil runs out the side plug on gearbox. Check gearbox daily for evi- dence of leakage, and contact your dealer if leakage occurs. Use sealant on vent plug threads during instal- lation. Check vent plug periodically and clean if it doesn’t relieve pressure.

Driveline Lubrication

1.Lubricate the driveline slip joint every eight operating hours. Failure to maintain proper lubrication could result in damage to U-joints, gearbox, and driveline.

2.Lower cutter to ground, disconnect driveline from tractor PTO shaft, and slide halves apart but do not disconnect from each other.

Gearbox Lubrication

For gearbox, use a high quality gear oil with a viscosity index of 80W or 90W and an API service rating of GL–

3.Apply a bead of grease completely around male half where it meets female half. Slide drive halves over each other several times to distribute grease.

20 Owner Service

MAN0810 (9/24/2009)

 

 

Image 20
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be CarefulKeep Away Safety Connecting Cutter to Tractor OperationOperation Hydraulic ConnectionCutting Height Adjustment Interference CheckCV Driveline Turning Limits Tractor OperationShredding Cutter OperationMowing Tips Transporting Lock-UpPRE-OPERATION Check List Owners ResponsibilityBlocking Method Owner ServiceOwner Service Gearbox Lubrication LubricationDriveline Lubrication Blade Installation Figure Seasonal LubricationBlades Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureVertical Shaft Seal Repair Spindle BOX Horizontal Shaft Seal RepairSpindle Gearbox Repair Remove Gearbox from Cutter Disassemble GearboxSpindle Gearbox Assembly Reinstall Gearbox Assemble GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install Height Adjustment Cylinder Install SMV EmblemInstall Wheel and Hub Install TongueInstall Wing Cylinder & Lock-up Bar Install CV DriveInstall Wing Install Wing Wheel and Hub Figure Left Wing Lock-Up Bar InstalledInstall Hose Kit Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Install Chain or Belt Shielding Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0810 9/24/2009 Parts BW15LHMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid Wing Drive Assembly Bodioli and Pavesi NSSBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITWinch Kit Operation Winch Kit InstallationWinch KIT Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty