Woods Equipment BW15LH manual Install Height Adjustment Cylinder, Install SMV Emblem

Page 35

Install Height Adjustment Cylinder

Refer to Figure 23.

1.Attach base end of cylinder (21) to the spring arm (19) using clevis pin (32) and two cotter pins (80).

2.Extend cylinder rod and place transport lock bracket (22) over cylinder rod clevis.

3.Position cylinder rod and transport lock bracket between lugs on the wheel yoke tube and align holes.

4.Secure cylinder rod and transport lock bracket to the wheel yoke tube using clevis pin (34) and two cotter pins (80).

5.Install bushing (40), elbow, (41) and hose (42) to the base end of cylinder (21). See Install Hose Kit, page 39 for complete instructions.

NOTE: An optional ratchet (24) is available, and replaces the hydraulic cylinder. Install ratchet jack using the same procedure and hardware used for the installation of the hydraulic cylinder.

Install SMV Emblem

Refer to Figure 23.

1.Attach SMV mounting bracket (25) to left side of center section as shown using two carriage bolts (66) and flange lock nuts (68).

2.Attach SMV socket (26) to mounting bracket (25) using two carriage bolts (73) and lock nuts (77).

3.Attach SMV emblem (28) to SMV bracket (27) using two round head cap screws (78) and hex nuts (79).

Insert SMV bracket (27) and emblem (28) into socket (26).

19.Spring arm

20.Spring

21.Hydraulic cylinder 3 x 8

22.Transport lock-up

23.1-1/4 Cylinder stroke control kit

24.Rachet adjustabel link bundle

25.SMV Mounting link

26.SMV Socket

27.SMV Bracket

28.SMV Emblem

32.1 x 2.72 Headless pin

33.1 x 4.08 Headless pin

34.1 x 4.58 Headless pin

38.Spacer, 1"

40.1/2 x 1/4 Pipe reducer bushing

41.1/4 x 1/4 Elbow w/ 1/16 restricter

42.1/4 x 1/4 x 156 Hose

65.1/2 NC x 4-1/2 HHCS GR5

66.1/2 NC x 1 Carriage bolt, GR5

68.1/2 NC Flanged lock nut

73.5/16 NC x 3/4 Carriage bolt

77.5/16 NC Flanged lock nut

78.1/4 NC x 1/2 Round head screw

79.1/4 NC Hex nut

80.1/4 x 1-1/2 Cotter pin

Figure 23. Spring Arm and Cylinder Installation

MAN0810 (9/24/2009)

Assembly 35

 

 

Image 35
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesInstallation TrainingOperation TransportationMaintenance Storage Be Careful Safety & Instructional DecalsKeep Away Safety Hydraulic Connection Connecting Cutter to TractorOperation OperationTractor Operation Cutting Height AdjustmentInterference Check CV Driveline Turning LimitsShredding Cutter OperationMowing Tips Lock-Up TransportingOwners Responsibility PRE-OPERATION Check ListBlocking Method Owner ServiceOwner Service Gearbox Lubrication LubricationDriveline Lubrication Blade Removal Figure Blade Installation FigureSeasonal Lubrication BladesBlade Sharpening Slip Clutch Adjustment FigureServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingSeal Replacement Figure Dealer ServiceDealer Service Gearbox MaintenanceDisassemble Gearbox Vertical Shaft Seal Repair Spindle BOXHorizontal Shaft Seal Repair Spindle Gearbox Repair Remove Gearbox from CutterSpindle Gearbox Assembly Assemble Gearbox Reinstall GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install SMV Emblem Install Height Adjustment CylinderInstall Tongue Install Wheel and HubInstall Wing Cylinder & Lock-up Bar Install CV DriveInstall Wing Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Hose Kit Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Delivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListMAN0810 9/24/2009 BW15LH PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid NSS Wing Drive Assembly Bodioli and PavesiBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalWinch Kit Operation Winch Kit InstallationWinch KIT Optional Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Warranty