Woods Equipment BW15LH manual Safety & Instructional Decals, Be Careful

Page 11

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

MODEL NO.	SERIAL NO.
	Woods Equipment Company
	Oregon, Illinois, U.S.A.

1 - SERIAL NUMBER PLATE

PN 1006348 - Located on Wheel Rims

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

2- FRONT AMBER REFLECTOR (PN 1002940)

3- REAR RED REFLECTOR (PN 57123)

4 - PN 18869

DANGER

	SHIELD MISSING	18869-B
	DO NOT OPERATE - PUT SHIELD ON	18869-B
	DO NOT OPERATE - PUT SHIELD ON

MAN0810 (9/24/2009)	Safety 11
MAN0810 (9/24/2009)

Image 11

Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesInstallation TrainingOperation TransportationMaintenance Storage Be Careful Safety & Instructional DecalsKeep Away Safety Hydraulic Connection Connecting Cutter to TractorOperation OperationTractor Operation Cutting Height AdjustmentInterference Check CV Driveline Turning LimitsShredding Cutter OperationMowing Tips Lock-Up TransportingOwners Responsibility PRE-OPERATION Check ListBlocking Method Owner ServiceOwner Service Gearbox Lubrication LubricationDriveline Lubrication Blade Removal Figure Blade Installation FigureSeasonal Lubrication BladesBlade Sharpening Slip Clutch Adjustment FigureServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingSeal Replacement Figure Dealer ServiceDealer Service Gearbox MaintenanceDisassemble Gearbox Vertical Shaft Seal Repair Spindle BOXHorizontal Shaft Seal Repair Spindle Gearbox Repair Remove Gearbox from CutterSpindle Gearbox Assembly Assemble Gearbox Reinstall GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install SMV Emblem Install Height Adjustment CylinderInstall Tongue Install Wheel and HubInstall Wing Cylinder & Lock-up Bar Install CV DriveInstall Wing Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Hose Kit Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Delivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListMAN0810 9/24/2009 BW15LH PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid NSS Wing Drive Assembly Bodioli and PavesiBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalWinch Kit Operation Winch Kit InstallationWinch KIT Optional Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Warranty