Woods Equipment BW15LH manual Crossbar Removal

Page 31

CROSSBAR REMOVAL

1.It is necessary to gain access to bottom side of cutter for crossbar removal. See Blocking Method page 19.

NOTE: You will need to use either the puller screw (Item 6, Figure 14) or a small hydraulic jack to remove the crossbar.

2.Remove blades from crossbar as shown in Figure 13.

10.Crossbar assembly

11.Shim, 18 ga

12.Shim, 20 ga

13.Keyhole plate

14.Blade lock clip

36.Stump jumper pan

52. 1/2 NC x 1-1/4 HHCS

Figure 13. Blade Removal

3.Refer to Figure 14. Remove cotter pin from bottom of crossbar and remove nut and washer.

4.Attach a clevis (1) to each end of crossbar, using blade pins, and nuts.

5.Position tube assembly (5) with threaded nut (4) toward crossbar for puller screw removal or down for hydraulic jack removal.

6.For removal with puller screw, attach tube (5) to each clevis with bolts (2) and nuts (3). Place pad

(4)in nut and thread puller screw (6) into nut from bottom. Tighten until pad is solid against gearbox shaft. For best results, strike head of puller screw with a hammer while tightening with a wrench.

7.For removal with a jack, attach tube to each clevis with puller links (7), bolts (2), and nuts (3). Place jack on tube with end of jack pressing against gearbox shaft. Slowly apply force with jack.

NOTE: Hydraulic jack will not operate if tipped more than 90°. Use care to prevent bending cross- bar during removal.

1.Crossbar puller clevis

2.5/8 NC x 4-1/2 HHCS

3.5/8 NC Hex nut

4.Crossbar puller pad

5.Crossbar puller tube

6.Crossbar puller screw

7.Crossbar puller link

Figure 14. Crossbar Removal

(Rev. 3/3/2010) MAN0810 (9/24/2009)

Dealer Service 31

Image 31
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesInstallation TrainingOperation TransportationMaintenance Storage Be Careful Safety & Instructional DecalsKeep Away Safety Hydraulic Connection Connecting Cutter to TractorOperation OperationTractor Operation Cutting Height AdjustmentInterference Check CV Driveline Turning LimitsMowing Tips Cutter OperationShredding Lock-Up TransportingOwners Responsibility PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Driveline Lubrication LubricationGearbox Lubrication Blade Removal Figure Blade Installation FigureSeasonal Lubrication BladesBlade Sharpening Slip Clutch Adjustment FigureShielding Repair CleaningServicing Tires Safely Troubleshooting TroubleshootingSeal Replacement Figure Dealer ServiceDealer Service Gearbox MaintenanceDisassemble Gearbox Vertical Shaft Seal Repair Spindle BOXHorizontal Shaft Seal Repair Spindle Gearbox Repair Remove Gearbox from CutterSpindle Gearbox Assembly Assemble Gearbox Reinstall GearboxAssembly DisassemblySplitter Gearbox Repair Figure Removal from Cutter Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalJoint Disassembly Crossbar InstallationUniversal Joint Repair Joint Assembly Assembly Instructions AssemblyDealer SET-UP Instructions Install SMV Emblem Install Height Adjustment CylinderInstall Tongue Install Wheel and HubInstall Wing Install CV DriveInstall Wing Cylinder & Lock-up Bar Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Wing Driveline Install Wing Wheel Yoke Adjustment LinkInstall Hose Kit Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Delivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListMAN0810 9/24/2009 BW15LH PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Hydraulic cylinder 3 x 8 see Wing Assembly Part QTY Description Splitter Gearbox Assembly Shaft 1-3/4, 20 spline, center Wing & Center Gearbox Assembly Wing & Center Gearbox Assembly Center Deck Drive Assembly CV Drive Assembly Wing Drive Assembly Walterscheid NSS Wing Drive Assembly Bodioli and PavesiBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Front & Rear Rubber Shielding Wing Standard Front & Rear Chain Shielding Center Section Optional Front & Rear Chain Shielding Wing Optional Front & Rear Hydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalWinch KIT Optional Winch Kit InstallationWinch Kit Operation Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Warranty