Shindaiwa F222, 81372 manual 10/15-Hour Maintenance, Gearcase Lubrication T222 Only

Page 12

10/15-Hour Maintenance

Clean the spark plug and check the gap at the

0.024–0.028 inchelectrode. (0.6–0.7 mm)

T

Figure 22

50-Hour Maintenance

Every 10 to 15 hours of operation:

■Remove and clean the spark plug. Adjust the spark plug electrode gap to 0.024- 0.028 inch (0.6-0.7 mm). If the spark plug must be replaced, use only an BPMR6A or equivalent resistor type spark plug of the correct heat range. See Figure 22.

NOTE:

The BPMR6A also meets the requirements for electro-magnetic compliance (EMC).

CAUTION!

Before removing the spark plug, clean the area around the plug to prevent dirt and debris from getting into the engine’s internal parts.

Every 50 hours of operation (more frequently in dusty or dirty conditions):

Gearcase Lubrication (T222 Only)

1.To perform this operation, first remove the gearcase and debris shield from the outer tube as follows. See Figure 23.

■Remove the index bolt from the gearcase.

■Loosen the gearcase clamp screw.

■Loosen the four socket head cap screws that secure the cutting attachment shield.

■Slide the gearcase and cutting attachment shield off the tube. (Do not lose the two shims).

. Remove the filler plug and press new grease into the gearcase until old grease is purged from the gearcase, which can be seen in the outer tube cavity.

Shims

 

Outer Tube

 

4 Socket Head Screws

4 Socket Head

 

Screws

 

Clamp Screw

 

Outer Tube

Old Grease

 

Cavity

 

Index Bolt

 

New Grease

 

Grease Plug

 

Figure 23

 

3.Clean up the excess grease and rein- stall the cutting attachment shield, two shims and the gearcase.

Remove and replace the filter element.

CAUTION!

Make sure you do not pierce the fuel line with the end of the hooked wire. The line is delicate and can be damaged easily.

1.Use a hooked wire to extract the fuel filter from inside the fuel tank. See Figure 24.

Before reinstalling the new filter element, inspect the condition of all the fuel system components (fuel pick-up line, fuel return line, tank vent line, tank vent, fuel cap and fuel tank). If damage, splitting or deterioration is noted, the unit should be removed from service until it can be inspected or repaired by a Shindaiwa-trained service technician.

Hooked

Filter Element

Wire

 

Figure 24

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents T222 Trimmer F222 Trimmer Contents IntroductionSafety Instructions Properly Equipped OperatorWork Safely Stay Alert Minimize the Risk of FireBe Aware of the Working Environment FeetSpecifications Prior to AssemblyProduct Description Assembly and Adjustments Adjust Throttle Lever Free PlayHandle Assembly Install the Cutting Attachment Shield T222Install the Cutting Attachment Shield F222 Cutting Attachment ShieldMixing Fuel Filling the Fuel TankStarting the Engine Be used in your Shindaiwa engineWhen the Engine Starts Idle Speed AdjustmentStopping the Engine Never start the engine from the operating positionChecking Unit Condition Cutting GrassEngine Operating Speeds Trimming and Mowing GrassGeneral Maintenance Daily MaintenanceHour Maintenance 10/15-Hour Maintenance Gearcase Lubrication T222 OnlyRemove and replace the filter element Long Term Storage Every 100 hours of operation, removeTroubleshooting Guide Engine does not StartAdditional Problems Manufacturers Warranty Coverage OWNER’S Warranty ResponsibilitiesMaintenance and Repair Requirements Obtaining Warranty ServicePodadora T222 Podadora F222 ¡ADVERTENCIAIntroducción Declaraciones de Seguridad ¡PRECAUCiÓNNota Instrucciones de Seguridad El Operario Debidamente EquipadoEsté Alerta En Su Área De Trabajo Etiquetas de SeguridadPies Descripción del Producto EspecificacionesAntes de Ensamblar Ensamblaje y Ajustes Ajuste la holgura del aceleradorEnsamblaje ¡PRECAUCIÓNMezcla de Combustible Llenando el Tanque de CombustibleArranque del Motor Ejemplos de cantidades de mezcla a proporción deArranque del Motor continuación Parada del MotorAjuste de Marcha Mínima del Motor Cuando arranca el motor…Verifique la Condición de la Unidad Corte de Césped Máquinas Equipadas con Cabezal de CorteVelocidades de operación del motor Cortar y recortar el céspedMantenimiento General Mantenimiento DiarioMantenimiento Cada 10 Horas Mantenimiento Cada 10/15 Horas Mantenimiento Cada 50 HorasRetire y reemplace el elemento del filtro Cada 100 horas Mantenimiento Almacenamiento de Largo PlazoGuia Diagnostico El Motor No ArrancaGuia Diagnostico continuación Problemas AdicionalesEsta Garantía ES Administrada POR Cobertura DE LA Garantía DEL FabricantePiezas Cubiertas LimitacionesDébroussailleuses T222 F222 AvertissementIntroduction Mises en garde Table des matièresAvertissement ! Les gaz d’échappement du Mise EN GardeMesures de sécurité Équipement complet de l’utilisateurSécurité au travail Demeurer alerteTenir compte de l’environnement de travail Étiquettes de sécuritéNomenclature Caractéristiques techniquesAvant l’assemblage Assemblage et réglage Réglage du jeu du levier d’accélérationPoignée Installation du déflecteur T222 Installation du déflecteur F222Tête de coupe Installer la tête de coupe AssemblageMélange de carburant Remplissage du réservoir à carburantDémarrage du moteur Réduire les risques d’incendieDémarrage du moteur suite Arrêt du moteurRéglage du ralenti du moteur Lorsque le moteur démarreContrôle de l’état de l’appareil Vitesses de fonctionnement du moteurTailler et tondre la pelouse Faire les borduresEntretien Entretien quotidienEntretien aux 10 heures Retrait et remplacement de l’élément du filtre Entretien aux 10 à 15 heuresToutes les 10 à 15 heures de fonctionnement Lubrification du boîtier réducteur T222 seulementEntretien aux 100 heures Remisage à long termeGuide de dépannage Des segmentsGuide de dépannage suite Autres ProblèmesÉtendue DE LA Garantie DU Fabricant Pièces Prises EN ChargeExigences Relatives À L’ENTRETIEN ET LA Réparation LA Présente Garantie EST Gérée PARRemarques FR18 FR19

81372, T222, F222 specifications

The Shindaiwa F222, 81372, and T222 are notable models within Shindaiwa's robust lineup of landscaping equipment, particularly designed for professional use. These tools are engineered to deliver high performance and reliability, making them ideal for both commercial landscapers and dedicated homeowners.

The Shindaiwa F222 is a powerful handheld blower known for its superior air speed and volume. With an exceptional engine output, it efficiently clears debris from various surfaces including lawns, gardens, and walkways. Its lightweight design ensures ease of use, reducing fatigue during extended operation. The F222 features an ergonomic handle that allows for a comfortable grip, and its well-balanced construction guarantees stability when in use. Additionally, the blower incorporates a low-emission engine technology, adhering to stringent environmental standards while still delivering ample power.

The Shindaiwa 81372 is recognized for its versatility as a hedge trimmer. This model boasts a dual-sided blade that provides a clean and precise cut, making it perfect for shaping and maintaining hedges and shrubs. The 81372 is equipped with a smooth-running, low-vibration motor that enhances user comfort, particularly during prolonged use. Furthermore, its lightweight and compact design make maneuvering easy, allowing operators to access tight spaces without hassle. With a focus on durability, Shindaiwa has designed the 81372’s blades to resist wear and maintain sharpness over time, ensuring longevity and optimal performance.

The T222, a robust trimmer, showcases Shindaiwa's commitment to power and efficiency. Engineered with a high-performance engine, the T222 delivers fast and efficient cutting, making it suitable for tackling thick grass and weeds. Its adjustable cutting head adds to its versatility, enabling users to reach various angles with ease. Additionally, the T222 is built with a comfortable grip and user-friendly interface, allowing for extended use without discomfort. Its lightweight construction makes it easy to handle, reducing the strain on the operator.

Across these models, Shindaiwa emphasizes innovative technologies, such as anti-vibration systems and fuel-efficient engines, ensuring that users can rely on their tools for productivity without compromising comfort. Overall, the Shindaiwa F222, 81372, and T222 represent a blend of power, efficiency, and user-friendly features, making them essential tools for landscaping professionals and enthusiasts alike.
Top Page Image Contents