Shindaiwa 81372, F222, T222 manual Troubleshooting Guide, Engine does not Start

Page 14

Troubleshooting Guide

ENGINE DOES NOT START

What To Check

Does the engine crank?

YES

Good compression?

YES

Does the tank contain fresh fuel of the proper grade?

YES

Is fuel visible and moving in the return line when priming?

YES

Is there spark at the spark plug wire terminal?

YES

Check the spark plug.

 

 

 

Possible Cause

 

NO

 

Faulty recoil starter.

 

 

 

 

Fluid in the crankcase.

 

 

 

 

 

Internal damage.

 

 

 

Loose spark plug.

 

NO

 

 

 

 

Excess wear on cylinder, piston, rings.

 

NO

 

Fuel incorrect, stale or contaminated;

 

 

 

 

mixture incorrect.

 

 

 

 

NO

 

Check for clogged fuel filter and/or vent.

 

 

 

 

 

 

 

 

 

Priming pump not functioning properly.

 

NO

 

The ignition switch is in “O” (OFF)

 

 

 

 

 

 

position.

 

 

 

 

 

 

Shorted ignition ground.

 

 

 

Faulty ignition unit.

 

 

 

If the plug is wet, excess fuel may be in

 

 

 

 

 

 

the cylinder.

 

 

 

 

 

 

The plug is fouled or improperly gapped.

 

 

 

The plug is damaged internally or of the

 

 

 

wrong size.

 

 

 

 

Remedy

Consult with an authorized servicing dealer.

Tighten and re-test.

Consult with an authorized servicing dealer.

Refill with fresh, clean unleaded gasoline with a pump octane of 87 or higher mixed with

a 2-cycle air cooled mixing oil that meets or exceeds ISO-L-EGD and/or JASO FC classified oils at 50:1 gasoline/oil ratio.

Replace fuel filter or vent as required; restart.

Consult with an authorized servicing dealer.

Move switch to “I” (ON) position and restart.

Consult with an authorized servicing dealer.

Crank the engine with the plug removed, reinstall the plug, and restart.

Clean and regap the plug to 0.024 - 0.028 inch (0.6 - 0.7 mm). Restart.

Replace the plug with an BPMR6A or equivalent resistor type spark plug of the correct heat range. Set spark plug electrode gap to 0.024-0.028 inch (0.6-0.7 mm).

LOW POWER OUTPUT

What To Check

Is the engine overheating?

Possible Cause

Operator is overworking the unit. Carburetor mixture is too lean. Improper fuel ratio.

Fan, fan cover, cylinder fins dirty or damaged.

Carbon deposits on the piston or in the muffler.

Remedy

Shorten trimmer line. Cut at a slower rate.

Consult with an authorized servicing dealer.

Refill with fresh, clean unleaded gasoline with a pump octane of 87 or higher mixed with

a 2-cycle air cooled mixing oil that meets or exceeds ISO-L-EGD and/or JASO FC classified oils at 50:1 gasoline/oil ratio.

Clean, repair or replace as necessary.

Consult with an authorized servicing dealer.

Engine is rough at all speeds. May also have black smoke and/or unburned fuel at the exhaust.

Engine is knocking.

Clogged air cleaner element. Loose or damaged spark plug.

Air leakage or clogged fuel line. Water in the fuel.

Piston seizure.

Faulty carburetor and/or diaphragm.

Overheating condition.

Improper fuel.

Carbon deposits in the combustion chamber.

Service the air cleaner element.

Tighten or replace. Replace the plug with an BPMR6A or equivalent resistor type spark plug of the correct heat range.

Repair or replace filter and/or fuel line.

Replace the fuel. See page 8.

Consult with an authorized servicing dealer.

See above.

Check fuel octane rating; check for presence of alcohol in the fuel (pg. 8). Refuel as necessary.

Consult with an authorized servicing dealer.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents T222 Trimmer F222 Trimmer Contents IntroductionWork Safely Safety InstructionsProperly Equipped Operator Stay Alert Minimize the Risk of FireBe Aware of the Working Environment FeetProduct Description SpecificationsPrior to Assembly Handle Assembly and AdjustmentsAdjust Throttle Lever Free Play Install the Cutting Attachment Shield F222 AssemblyInstall the Cutting Attachment Shield T222 Cutting Attachment ShieldStarting the Engine Mixing FuelFilling the Fuel Tank Be used in your Shindaiwa engineStopping the Engine When the Engine StartsIdle Speed Adjustment Never start the engine from the operating positionEngine Operating Speeds Checking Unit ConditionCutting Grass Trimming and Mowing GrassHour Maintenance General MaintenanceDaily Maintenance Remove and replace the filter element 10/15-Hour MaintenanceGearcase Lubrication T222 Only Long Term Storage Every 100 hours of operation, removeTroubleshooting Guide Engine does not StartAdditional Problems Maintenance and Repair Requirements Manufacturers Warranty CoverageOWNER’S Warranty Responsibilities Obtaining Warranty ServicePodadora T222 Podadora F222 ¡ADVERTENCIANota Introducción Declaraciones de Seguridad¡PRECAUCiÓN Instrucciones de Seguridad El Operario Debidamente EquipadoPies Esté Alerta En Su Área De TrabajoEtiquetas de Seguridad Antes de Ensamblar Descripción del ProductoEspecificaciones Ensamblaje y Ajustes Ajuste la holgura del aceleradorEnsamblaje ¡PRECAUCIÓNArranque del Motor Mezcla de CombustibleLlenando el Tanque de Combustible Ejemplos de cantidades de mezcla a proporción deAjuste de Marcha Mínima del Motor Arranque del Motor continuaciónParada del Motor Cuando arranca el motor…Velocidades de operación del motor Verifique la Condición de la UnidadCorte de Césped Máquinas Equipadas con Cabezal de Corte Cortar y recortar el céspedMantenimiento Cada 10 Horas Mantenimiento GeneralMantenimiento Diario Retire y reemplace el elemento del filtro Mantenimiento Cada 10/15 HorasMantenimiento Cada 50 Horas Cada 100 horas Mantenimiento Almacenamiento de Largo PlazoGuia Diagnostico El Motor No ArrancaGuia Diagnostico continuación Problemas AdicionalesPiezas Cubiertas Esta Garantía ES Administrada PORCobertura DE LA Garantía DEL Fabricante LimitacionesDébroussailleuses T222 F222 AvertissementAvertissement ! Les gaz d’échappement du Introduction Mises en gardeTable des matières Mise EN GardeSécurité au travail Mesures de sécuritéÉquipement complet de l’utilisateur Demeurer alerteTenir compte de l’environnement de travail Étiquettes de sécuritéAvant l’assemblage NomenclatureCaractéristiques techniques Poignée Assemblage et réglageRéglage du jeu du levier d’accélération Tête de coupe Installer la tête de coupe Installation du déflecteur T222Installation du déflecteur F222 AssemblageDémarrage du moteur Mélange de carburantRemplissage du réservoir à carburant Réduire les risques d’incendieRéglage du ralenti du moteur Démarrage du moteur suiteArrêt du moteur Lorsque le moteur démarreTailler et tondre la pelouse Contrôle de l’état de l’appareilVitesses de fonctionnement du moteur Faire les borduresEntretien aux 10 heures EntretienEntretien quotidien Toutes les 10 à 15 heures de fonctionnement Retrait et remplacement de l’élément du filtreEntretien aux 10 à 15 heures Lubrification du boîtier réducteur T222 seulementEntretien aux 100 heures Remisage à long termeGuide de dépannage Des segmentsGuide de dépannage suite Autres ProblèmesExigences Relatives À L’ENTRETIEN ET LA Réparation Étendue DE LA Garantie DU FabricantPièces Prises EN Charge LA Présente Garantie EST Gérée PARRemarques FR18 FR19

81372, T222, F222 specifications

The Shindaiwa F222, 81372, and T222 are notable models within Shindaiwa's robust lineup of landscaping equipment, particularly designed for professional use. These tools are engineered to deliver high performance and reliability, making them ideal for both commercial landscapers and dedicated homeowners.

The Shindaiwa F222 is a powerful handheld blower known for its superior air speed and volume. With an exceptional engine output, it efficiently clears debris from various surfaces including lawns, gardens, and walkways. Its lightweight design ensures ease of use, reducing fatigue during extended operation. The F222 features an ergonomic handle that allows for a comfortable grip, and its well-balanced construction guarantees stability when in use. Additionally, the blower incorporates a low-emission engine technology, adhering to stringent environmental standards while still delivering ample power.

The Shindaiwa 81372 is recognized for its versatility as a hedge trimmer. This model boasts a dual-sided blade that provides a clean and precise cut, making it perfect for shaping and maintaining hedges and shrubs. The 81372 is equipped with a smooth-running, low-vibration motor that enhances user comfort, particularly during prolonged use. Furthermore, its lightweight and compact design make maneuvering easy, allowing operators to access tight spaces without hassle. With a focus on durability, Shindaiwa has designed the 81372’s blades to resist wear and maintain sharpness over time, ensuring longevity and optimal performance.

The T222, a robust trimmer, showcases Shindaiwa's commitment to power and efficiency. Engineered with a high-performance engine, the T222 delivers fast and efficient cutting, making it suitable for tackling thick grass and weeds. Its adjustable cutting head adds to its versatility, enabling users to reach various angles with ease. Additionally, the T222 is built with a comfortable grip and user-friendly interface, allowing for extended use without discomfort. Its lightweight construction makes it easy to handle, reducing the strain on the operator.

Across these models, Shindaiwa emphasizes innovative technologies, such as anti-vibration systems and fuel-efficient engines, ensuring that users can rely on their tools for productivity without compromising comfort. Overall, the Shindaiwa F222, 81372, and T222 represent a blend of power, efficiency, and user-friendly features, making them essential tools for landscaping professionals and enthusiasts alike.
Top Page Image Contents