Shindaiwa EB212, 82051 manual Spark plug, Cooling system

Page 16

English

Spark plug

Level 2.

Tools required: 3/4 in. Spark Plug deep socket, Feeler gauge

IMPORTANT

Use only BPMR-8Y spark plug otherwise severe engine damage may occur.

1.Remove spark plug and check for fouling, worn and rounded center electrode.

2.Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine.

3.

Adjust spark plug gap by bending outer electrode.

0.65 mm

(0.026 in.)

 

 

4.

Tighten spark plug to 150-170 kg/cm (130-150 in. lb.).

 

 

 

 

 

Cooling system

Level 2.

Tools required: 25-50 mm (1-2 in.) Cleaning brush, 3 mm Hex

Wrench, Cross Head Screwdriver

Parts Required: None, if you are careful.

IMPORTANT

To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area. This flow of air carries combustion heat away from the engine.

Overheating and engine seizure can occur when:

•Air intakes are blocked, preventing cooling air from reaching the cylinder.

•Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling fins is considered “Normal Maintenance”. Any failure attributed to lack of maintenance is not warranted.

Cleaning Grill

1. Brush accumulated debris from crankcase intake grill above the fuel tank.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents EB212 Blower Introduction Table of ContentsOperator’s manual International symbols Safety Manual safety symbols and important informationPersonal condition and safety equipment Physical Condition Eye ProtectionHand Protection Breathing ProtectionRepetitive Stress Injuries Read the ManualsClear the Work Area Keep a Firm GripEPA Phase 2/ C.A.R.B. Tier Equipment checkEmission Control Product Emission DurabilitySound Label DescriptionContents Install Blower Pipes AssemblyBlower application Operation FuelHandling Fuel Fuel RequirementsMetric Starting cold engine Purge BulbStarting warm engine Stopping engineOperating blower Maintenance intervals MaintenanceSkill levels Air filter Fuel filterSpark plug Cooling systemSpark Arrestor Screen Exhaust systemHigh Altitude Adjustment Carburetor adjustmentCylinder Exhaust Port Engine Break-InTroubleshooting Troubleshooting ChartLong Term Storage Over 30 Days StorageSpecifications Model EB212 Hand HeldManufacturers Warranty Coverage Owners Warranty ResponsibilitiesWhat does this Warranty COVER? HOW will a Covered Part be CORRECTED?English English Sopladora EB212 El manual del operador IntroducciónTabla de materias Símbolos internacionales Condición personal y equipos de seguridadCondición física Protección de los ojosProtección de las manos Protección respiratoriaLesiones debidas a esfuerzos repetitivos PeligroCompruebe el equipo Fase 2 de EPA / Nivel III de C.A.R.BControl de emisiones Categoría DescripciónContenido Instale los tubos del soplador MontajeAplicación del soplador OperaciónManipulación del combustible Requisitos del combustibleImportante Arranque del motor en frío NotaArranque con el motor caliente Parada del motorOperación del soplador Nivel de habilidad Mantenimiento¡IMPORTANTE Filtro de aire Filtro de combustibleBujía Sistema de enfriamientoRejilla del apagachispas Sistema de escapeOrificio de escape del cilindro Rodaje del motorAjuste de altitud elevada Ajuste del carburadorLocalización y reparación de fallas Almacenamiento a largo plazo más de 30 días AlmacenamientoEspecificaciones ModeloRelacionados CON LAS Emisiones EPA Phase California Tier III Emissions Defect Warranty ENRelacionados CON Emisiones EPA Phase 2 / California Piezas Cubiertas POR LA Garantía Contra DefectosNotas Asaminami-Ku, Hiroshima EB212 Soufflante Le manuel d’utilisation Table des matièresSymboles internationaux Sécurité Symboles de sécurité et informations importantesCondition physique et equipement de sécurité Condition physique Protection des yeuxProtection des mains Protection des voies respiratoiresMicrotraumatismes répétés Lisez les manuelsContrôle des émissions Vérifiez l’équipementDurabilité DU Contrôle DES Émissions Autocollants de niveau sonore Sur le corps de la soufflanteContenu Installation des tubes de soufflante AssemblageUtilisation CarburantSpécifications pour le carburant Manipulation du carburantDémarrage d’un moteur froid RemarqueDémarrage d’un moteur chaud Arrêt du moteurUtilisation de la soufflante Niveaux de difficulte EntretienIntervalles d’entretien Fitlre à air Filtre a carburantBougie Système de refroidissementPare-étincelles Système déchappementLumière d’échappement du cylindre Rodage du moteurRéglage pour haute altitude Réglage du carburateurDépannage Remisage à long terme plus de 30 jours RemisageCaractéristiques Modele EB212 à mainCouverture DE LA Garantie DES Fabricants Responsabilités DU Propriétaire À L’ÉGARD DE LA GarantieEN CAS DE Pièce Défectueuse CE QUE Couvre Cette GarantieRemarques

82051, EB212 specifications

The Shindaiwa 82051 and EB212 are top-tier products that cater to a variety of outdoor maintenance needs, particularly in the realm of landscaping and gardening. Shindaiwa, a well-known name in the outdoor power equipment market, consistently delivers high-quality equipment designed for reliability and performance.

The Shindaiwa 82051 is primarily recognized as a premium brushcutter, engineered to handle tough cutting jobs with ease. One of its standout features is its powerful 22.5 cc, 2-cycle engine, which ensures robust performance and efficient fuel consumption. This engine type provides exceptional torque and power, making it capable of tackling dense vegetation.

The 82051 model also boasts a lightweight and ergonomic design that enhances user comfort and control during operation. The handlebars are designed for a relaxed grip, and the overall weight of the unit ensures that fatigue is minimized, allowing users to work longer without discomfort. Additionally, the product comes equipped with a dynamic shoulder strap that distributes the weight evenly, thus providing improved balance and maneuverability.

Commercial users will appreciate the Shindaiwa 82051's durability, as it features high-quality materials that withstand the rigors of daily use. The air filtration system is designed to reduce engine wear, prolonging the life of the machine and ensuring reliability even under rigorous conditions.

On the other hand, the Shindaiwa EB212 leaf blower is an essential tool for those in need of effective yard cleanup. This leaf blower features a powerful 21.2 cc engine, delivering an impressive airflow of up to 422 CFM (cubic feet per minute) and a maximum air speed of 165 mph. These features make the EB212 incredibly effective in managing debris, whether it be leaves, grass clippings, or other yard waste.

One of the highlighted technologies in the EB212 is the innovative two-stroke engine that ensures lower emissions without sacrificing performance, in line with environmental standards. The unit also features an ergonomic design with a comfortable grip and lightweight build, making it easy to maneuver for extended periods.

In summary, both the Shindaiwa 82051 and EB212 bring together power, efficiency, and user-centered designs. Their features cater to professionals and homeowners alike, standing out for their performance, durability, and comfort, making them indispensable tools for outdoor maintenance. Whether tackling stubborn brush or managing leaves, these machines reaffirm Shindaiwa's commitment to quality and innovation in outdoor power equipment.
Top Page Image Contents