Shindaiwa EB212, 82051 manual Cylinder Exhaust Port, Engine Break-In, High Altitude Adjustment

Page 18

English

Cylinder Exhaust Port

Level 3.

IMPORTANT

The cylinder exhaust port must be inspected and cleaned of excess carbon every 3 months or 90 hours of operation in order to main- tain this engine within the emissions durability period. Shindaiwa strongly recommends that you return your unit to your Shindaiwa dealer for this important maintenance service.

Carburetor adjustment

Engine Break-In

New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break- in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required.

High Altitude Adjustment

High altitude adjustment is not required for proper operation of this engine.

Level 2.

Tools required: Screwdriver, tachometer

Parts required: None.

NOTE

Every unit is run at the factory and the carburetor is set in com- pliance with emission regulations. This carburetor does not have acceleration and high speed adjustment needles.

1.Before adjusting the carburetor, clean or replace the air filter and spark arrestor screen and blower pipes are installed.

2.Start engine and run for several minutes to reach operating temperature.

3.Stop engine. Turn red HI speed needle (A) CCW (counter clockwise) to stop.

4.Idle Speed Adjustment with tachometer.

•Start engine and turn “idle” speed adjustment screw (B) to idle RPM found on page 21 in the "Specifications" section of this manual.

5.Accelerate to full throttle for 2-3 seconds to clear excess fuel from engine then return to idle. Accelerate to full throttle to check for smooth transition from idle to full throttle. If engine stops or stalls after full warm up return the unit to your authorized Shindaiwa dealer for repair.

6.Check HI speed RPM at W.O.T. (Wide Open Throttle). HI speed RPM should be set to specifications found on page 21 "Specifications" of this manual.

7.Check idle speed and reset if necessary.

A

B

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents EB212 Blower Table of Contents IntroductionOperator’s manual Safety Manual safety symbols and important information International symbolsPersonal condition and safety equipment Hand Protection Physical ConditionEye Protection Breathing ProtectionClear the Work Area Repetitive Stress InjuriesRead the Manuals Keep a Firm GripEmission Control EPA Phase 2/ C.A.R.B. TierEquipment check Product Emission DurabilitySound Label DescriptionContents Blower application Install Blower PipesAssembly Operation FuelFuel Requirements Handling FuelMetric Starting cold engine Purge BulbStarting warm engine Stopping engineOperating blower Maintenance Maintenance intervalsSkill levels Air filter Fuel filterSpark plug Cooling systemSpark Arrestor Screen Exhaust systemCylinder Exhaust Port High Altitude AdjustmentCarburetor adjustment Engine Break-InTroubleshooting Troubleshooting ChartLong Term Storage Over 30 Days StorageSpecifications Model EB212 Hand HeldWhat does this Warranty COVER? Manufacturers Warranty CoverageOwners Warranty Responsibilities HOW will a Covered Part be CORRECTED?English English Sopladora EB212 Introducción El manual del operadorTabla de materias Símbolos internacionales Condición personal y equipos de seguridadProtección de las manos Condición físicaProtección de los ojos Protección respiratoriaLesiones debidas a esfuerzos repetitivos PeligroFase 2 de EPA / Nivel III de C.A.R.B Compruebe el equipoControl de emisiones Categoría DescripciónContenido Aplicación del soplador Instale los tubos del sopladorMontaje OperaciónRequisitos del combustible Manipulación del combustibleImportante Arranque del motor en frío NotaArranque con el motor caliente Parada del motorOperación del soplador Mantenimiento Nivel de habilidad¡IMPORTANTE Filtro de aire Filtro de combustibleBujía Sistema de enfriamientoRejilla del apagachispas Sistema de escapeAjuste de altitud elevada Orificio de escape del cilindroRodaje del motor Ajuste del carburadorLocalización y reparación de fallas Almacenamiento a largo plazo más de 30 días AlmacenamientoEspecificaciones ModeloRelacionados CON Emisiones EPA Phase 2 / California Relacionados CON LAS Emisiones EPA PhaseCalifornia Tier III Emissions Defect Warranty EN Piezas Cubiertas POR LA Garantía Contra DefectosNotas Asaminami-Ku, Hiroshima EB212 Soufflante Le manuel d’utilisation Table des matièresSécurité Symboles de sécurité et informations importantes Symboles internationauxCondition physique et equipement de sécurité Protection des mains Condition physiqueProtection des yeux Protection des voies respiratoiresMicrotraumatismes répétés Lisez les manuelsVérifiez l’équipement Contrôle des émissionsDurabilité DU Contrôle DES Émissions Autocollants de niveau sonore Sur le corps de la soufflanteContenu Utilisation Installation des tubes de soufflanteAssemblage CarburantSpécifications pour le carburant Manipulation du carburantDémarrage d’un moteur froid RemarqueDémarrage d’un moteur chaud Arrêt du moteurUtilisation de la soufflante Entretien Niveaux de difficulteIntervalles d’entretien Fitlre à air Filtre a carburantBougie Système de refroidissementPare-étincelles Système déchappementRéglage pour haute altitude Lumière d’échappement du cylindreRodage du moteur Réglage du carburateurDépannage Remisage à long terme plus de 30 jours RemisageCaractéristiques Modele EB212 à mainEN CAS DE Pièce Défectueuse Couverture DE LA Garantie DES FabricantsResponsabilités DU Propriétaire À L’ÉGARD DE LA Garantie CE QUE Couvre Cette GarantieRemarques

82051, EB212 specifications

The Shindaiwa 82051 and EB212 are top-tier products that cater to a variety of outdoor maintenance needs, particularly in the realm of landscaping and gardening. Shindaiwa, a well-known name in the outdoor power equipment market, consistently delivers high-quality equipment designed for reliability and performance.

The Shindaiwa 82051 is primarily recognized as a premium brushcutter, engineered to handle tough cutting jobs with ease. One of its standout features is its powerful 22.5 cc, 2-cycle engine, which ensures robust performance and efficient fuel consumption. This engine type provides exceptional torque and power, making it capable of tackling dense vegetation.

The 82051 model also boasts a lightweight and ergonomic design that enhances user comfort and control during operation. The handlebars are designed for a relaxed grip, and the overall weight of the unit ensures that fatigue is minimized, allowing users to work longer without discomfort. Additionally, the product comes equipped with a dynamic shoulder strap that distributes the weight evenly, thus providing improved balance and maneuverability.

Commercial users will appreciate the Shindaiwa 82051's durability, as it features high-quality materials that withstand the rigors of daily use. The air filtration system is designed to reduce engine wear, prolonging the life of the machine and ensuring reliability even under rigorous conditions.

On the other hand, the Shindaiwa EB212 leaf blower is an essential tool for those in need of effective yard cleanup. This leaf blower features a powerful 21.2 cc engine, delivering an impressive airflow of up to 422 CFM (cubic feet per minute) and a maximum air speed of 165 mph. These features make the EB212 incredibly effective in managing debris, whether it be leaves, grass clippings, or other yard waste.

One of the highlighted technologies in the EB212 is the innovative two-stroke engine that ensures lower emissions without sacrificing performance, in line with environmental standards. The unit also features an ergonomic design with a comfortable grip and lightweight build, making it easy to maneuver for extended periods.

In summary, both the Shindaiwa 82051 and EB212 bring together power, efficiency, and user-centered designs. Their features cater to professionals and homeowners alike, standing out for their performance, durability, and comfort, making them indispensable tools for outdoor maintenance. Whether tackling stubborn brush or managing leaves, these machines reaffirm Shindaiwa's commitment to quality and innovation in outdoor power equipment.
Top Page Image Contents