North Star M1108D Before Each Use Work Site Selection & Set-Up, Fire precautions, Select location

Page 18

Before Each Use – Work Site Selection & Set-Up

Step Three: Work site selection and log splitter set-up

WARNING

It is important to select an appropriate work site and properly set up the log splitter in order to minimize the risk of slips and falls, equipment rolling or tipping over, carbon monoxide poisoning, and accidental fires.

1. Select location

2.Fire precautions

3. Position splitter 7’ from any combustibles or flammable liquids

Select an appropriate location for operating the log splitter.

Requirements:

1.Dry-level surface with good footing. Stay clear of areas with mud, ice, tall grass, weeds, brush, or snow.

2.Outdoors, away from air intakes.

WARNING: The running engine gives off carbon monoxide, a poisonous gas that can kill you. You CANNOT smell it, see it, or taste it.

•ONLY run log splitter OUTDOORS and away from air intakes. NEVER run log splitter inside homes, garages, sheds, or other buildings or semi-enclosed spaces. These spaces can trap poisonous gases, EVEN if you run a fan or open windows.

•If you start to feel sick, dizzy, or weak while using the log splitter, shut off the engine and get to fresh air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.

Take the following precautions against fire:

1.IMPORTANT: If your splitter will be used near any unimproved forest, brush, or grassy covered land, then engine must be equipped with a spark arrestor.

(See the “Specifications” section of this manual to determine if your splitter already has a spark arrestor. Contact Northstar Customer Service at 1-800-270-0810 for information about obtaining a spark arrestor for your log splitter if it is unequipped.)

2.Make sure you comply with applicable local, state and federal codes.

3.Keep a fire extinguisher available (classified for both ordinary combustibles & flammable liquids) as a precautionary measure when operating the log splitter in dry areas.

Position muffler at least 7 ft. from combustible objects during operation.

Hot exhaust fumes from engine could cause fire. Also, hydraulic oil leaking or spraying on hot engine can ignite.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents M1108D Hazard Signal Word Definitions Table of Contents This equipment to others Warranty RegistrationAbout Your Log Splitter About Your Log SplitterSafety Label Locations Split Control Lever Operation Machine Component Identification DescriptionInitial Set-Up Wear between the keepers and beam Way Wedge Wings Wing Assembly Optional 4-Way Wedge WingsMoving and Towing to the Job Site Moving the log splitterImportant Make sure log splitter engine is off Towing Put front outrigger legAttach log splitter to vehicle hitch Important safety instructions Remove debris from engine, muffler, and moving parts Before Each Use-Inspection / MaintenanceStep One Inspect and maintain log splitter before each use Check fuel tank and fuel lines for leaksHydraulic system Check the hydraulic system carefully Before Each Use-Inspection / Maintenance Before Each Use Fueling Remove gas cap Remove engine gas capAdd gasoline Step Three Work site selection and log splitter set-up Fire precautionsBefore Each Use Work Site Selection & Set-Up Select locationLock both outrigger legs Block wheels Apply greaseLock both the outrigger legs in the Down position General safety information Splitting OperationOr vertical Set toHorizontal ClothingLock rear outrigger leg in down position Vertical positionFingers or cause damage to the splitter Load log Correct Log OrientationExtend wedge Stop wedgeRemove split wood from area Return wedgeRemove split wood After use Turn off engine Remove engine debrisStorage Short-Term StoragePeriodic Maintenance As specified in spark arrestor muffler manual Troubleshooting Any Questions, Comments, Problems or Parts OrdersSpecifications Parts Breakdown Exploded View 1108, 1109, 1114 Rev D ALL Summary of Important Safety Information for Operation Safety Before Use Read/instruct Safety During Inspection/MaintenancePersonal protective equipment Safety During Fueling Safety in Work Site SelectionSafety During Use General Safety During Use Safety in Loading, Operating, and UnloadingLoading/Unloading Safety After use Assembly Instructions Assembly Instructions Step Bolt Catch Pin Towbar Outrigger Leg Fasten Horizontal Beam Lock to 1114 models only Tighten Idle Control Bolts to 20 lb- ft with a wrench Return Line

M1108D specifications

The North Star M1108D is a versatile and advanced military vehicle designed to meet the rigorous demands of modern warfare. Known for its robustness and adaptability, the M1108D has been developed with state-of-the-art technologies and features that enhance its performance in diverse environments.

One of the standout features of the M1108D is its powerful drivetrain, equipped with a dependable turbocharged engine that delivers impressive horsepower and torque. This ensures the vehicle can traverse challenging terrains, whether urban landscapes or rugged off-road conditions, making it a reliable option for military operations.

The M1108D boasts an independent suspension system, providing excellent ride quality and stability, especially when navigating difficult ground surfaces. This system allows for improved handling, reducing the wear and tear on the vehicle while enhancing crew comfort during long missions.

In terms of protection, the vehicle is designed with advanced armor plating that offers a high level of ballistic and blast protection for its occupants. This ensures that personnel inside can operate with greater confidence, knowing they are shielded from potential threats. Additionally, the M1108D is equipped with upgraded defensive technologies such as smoke grenade launchers and jamming systems, further enhancing its survivability on the battlefield.

Another critical characteristic of the M1108D is its modular design, allowing for easy customization and adaptation. It can be configured for various roles, including troop transport, command and control, medical evacuation, or as a platform for weapon systems. This versatility makes it an ideal choice for diverse military operations.

The vehicle also integrates modern communication and navigation technologies, facilitating real-time coordination and situational awareness. These systems enhance operational effectiveness, allowing units to respond quickly and efficiently to evolving battlefield conditions.

Fuel efficiency is an essential aspect of the M1108D, as its engineering incorporates features that optimize consumption without compromising performance. This attribute extends operational range, ensuring that missions can be conducted with fewer logistical challenges.

Overall, the North Star M1108D exemplifies modern military vehicle design, combining durability, versatility, and advanced technological integration. Its myriad features make it a vital asset for armed forces, capable of adapting to the unpredictable nature of contemporary combat scenarios. As militaries around the world continue to evolve, the M1108D stands out as a reliable and effective solution for a range of operational needs.
Top Page Image Contents