North Star M1108D owner manual Safety During Use General Safety During Use, Loading/Unloading

Page 36

Summary of Important Safety Information for Operation

Safety – During Use

General Safety During Use

WARNING: Before starting this log splitter, review the following rules for safe operation. Failure to follow these rules may result in serious injury to the operator or bystanders.

•Safety equipment / controls. Always operate the log splitter with all safety equipment in place and in good working order, and all controls properly adjusted for safe operation.

•Operating speed. Always operate the log splitter at the manufacturer’s recommended speed. The maximum speed of the engine, pump and wedge are preset within safe limits.

•Know how to stop. Be thoroughly familiar with all controls and with the proper use of the equipment. Know how to stop the log splitter and relieve system pressures quickly if needed.

•Daylight only. Only use the log splitter in daylight so you can see what you are doing.

•Smoking / sparks. Never smoke while operating the log splitter, and never operate near sources of sparks or flames.

•Hot muffler. If you are starting a warm engine, stay clear of muffler. It may still be hot enough to burn you.

•Unattended. Never leave the machine unattended while the engine is running.

•Under the influence. Never operate, or let anyone else operate, the log splitter while under the influence of alcohol, drugs, or medication.

•Adjusting / repairing. Always make sure the engine is off before cleaning, repairing or adjusting the splitter, except as recommended by the manufacturer. In addition, disconnect the spark plug and move all control handles back and forth to relieve system pressure before changing or adjusting hydraulic system components such as hoses, tubing, fittings or other components.

•Carbon monoxide. The running engine gives off carbon monoxide, a poisonous gas that can kill you. You CANNOT smell it, see it, or taste it. If you start to feel sick, dizzy, or weak while using the log splitter, shut off the engine and get to fresh air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.

•Other exhaust dangers. Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Avoid inhalation of exhaust.

Safety in Loading, Operating, and Unloading

•Square log ends. Logs that are not cut square can slide out while splitting and become a safety hazard or cause excessive force to log splitter components. Use a chainsaw to cut logs square on each end before attempting to split them.

•Single log. Never attempt to split more than one log at a time. Pieces of log can unexpectedly be thrown from the machine causing serious injury.

•Split along grain. Do not use the log splitter to split logs across the grain. Doing so will damage the log splitter and could also cause pieces of log to be thrown, injuring the operator or bystanders.

•Keep hands clear. ALWAYS keep hands and feet away from the endplate, wedge, and partially split logs while loading, operating and unloading the log splitter.

•Operator position. ALWAYS operate the log splitter from the manufacturer’s indicated OPERATOR POSITION. Other positions are unsafe because they can increase the risk of injury from crushing, cutting, flying objects, or burns.

•Straddling / reaching across. Never straddle, reach across, or step over the beam while the engine is running and the log splitter is in the horizontal position. You could trip, actuate the controls, and get seriously injured.

•Second person. Many accidents occur when there is more than one person involved in loading and operating the log splitter. Only one person should operate the controls. If a second person is assisting in loading logs, the operator must NEVER actuate the Split Control Lever until the assistant and all bystanders are at least 10 feet away. NEVER allow an assistant to hold the log in place while the operator actuates the Split Control Lever.

•Loading/Unloading

•Unsplit log pile. Do not pile logs to be split in a place that will make you reach across the log splitter in order to load them.

•Hold bark side. Hold the bark side of logs when loading or positioning, never the ends. Never place your hands or any part of your body between a log and any part of the log splitter.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents M1108D Hazard Signal Word Definitions Table of Contents Warranty Registration About Your Log SplitterThis equipment to others About Your Log SplitterSafety Label Locations Split Control Lever Operation Machine Component Identification DescriptionInitial Set-Up Wear between the keepers and beam Way Wedge Wings Wing Assembly Optional 4-Way Wedge WingsMoving and Towing to the Job Site Moving the log splitterImportant Make sure log splitter engine is off Towing Put front outrigger legAttach log splitter to vehicle hitch Important safety instructions Before Each Use-Inspection / Maintenance Step One Inspect and maintain log splitter before each useRemove debris from engine, muffler, and moving parts Check fuel tank and fuel lines for leaksHydraulic system Check the hydraulic system carefully Before Each Use-Inspection / Maintenance Before Each Use Fueling Remove gas cap Remove engine gas capAdd gasoline Fire precautions Before Each Use Work Site Selection & Set-UpStep Three Work site selection and log splitter set-up Select locationLock both outrigger legs Block wheels Apply greaseLock both the outrigger legs in the Down position General safety information Splitting OperationSet to HorizontalOr vertical ClothingLock rear outrigger leg in down position Vertical positionFingers or cause damage to the splitter Load log Correct Log OrientationExtend wedge Stop wedgeReturn wedge Remove split wood After useRemove split wood from area Turn off engine Remove engine debrisStorage Short-Term StoragePeriodic Maintenance As specified in spark arrestor muffler manual Troubleshooting Any Questions, Comments, Problems or Parts OrdersSpecifications Parts Breakdown Exploded View 1108, 1109, 1114 Rev D ALL Summary of Important Safety Information for Operation Safety Before Use Read/instruct Safety During Inspection/MaintenancePersonal protective equipment Safety During Fueling Safety in Work Site SelectionSafety During Use General Safety During Use Safety in Loading, Operating, and UnloadingLoading/Unloading Safety After use Assembly Instructions Assembly Instructions Step Bolt Catch Pin Towbar Outrigger Leg Fasten Horizontal Beam Lock to 1114 models only Tighten Idle Control Bolts to 20 lb- ft with a wrench Return Line

M1108D specifications

The North Star M1108D is a versatile and advanced military vehicle designed to meet the rigorous demands of modern warfare. Known for its robustness and adaptability, the M1108D has been developed with state-of-the-art technologies and features that enhance its performance in diverse environments.

One of the standout features of the M1108D is its powerful drivetrain, equipped with a dependable turbocharged engine that delivers impressive horsepower and torque. This ensures the vehicle can traverse challenging terrains, whether urban landscapes or rugged off-road conditions, making it a reliable option for military operations.

The M1108D boasts an independent suspension system, providing excellent ride quality and stability, especially when navigating difficult ground surfaces. This system allows for improved handling, reducing the wear and tear on the vehicle while enhancing crew comfort during long missions.

In terms of protection, the vehicle is designed with advanced armor plating that offers a high level of ballistic and blast protection for its occupants. This ensures that personnel inside can operate with greater confidence, knowing they are shielded from potential threats. Additionally, the M1108D is equipped with upgraded defensive technologies such as smoke grenade launchers and jamming systems, further enhancing its survivability on the battlefield.

Another critical characteristic of the M1108D is its modular design, allowing for easy customization and adaptation. It can be configured for various roles, including troop transport, command and control, medical evacuation, or as a platform for weapon systems. This versatility makes it an ideal choice for diverse military operations.

The vehicle also integrates modern communication and navigation technologies, facilitating real-time coordination and situational awareness. These systems enhance operational effectiveness, allowing units to respond quickly and efficiently to evolving battlefield conditions.

Fuel efficiency is an essential aspect of the M1108D, as its engineering incorporates features that optimize consumption without compromising performance. This attribute extends operational range, ensuring that missions can be conducted with fewer logistical challenges.

Overall, the North Star M1108D exemplifies modern military vehicle design, combining durability, versatility, and advanced technological integration. Its myriad features make it a vital asset for armed forces, capable of adapting to the unpredictable nature of contemporary combat scenarios. As militaries around the world continue to evolve, the M1108D stands out as a reliable and effective solution for a range of operational needs.
Top Page Image Contents