North Star M1108D owner manual Extend wedge, Stop wedge

Page 24

Splitting Operation

6.Extend wedge

7. Stop wedge

8.Important

STUCK LOG procedure

Move Split Control Lever toward endplate to extend wedge and split log.

SPLIT CONTROL LEVER OPERATION

Important safety instructions:

•Operator position. ALWAYS operate the log splitter from the manufacturer’s indicated OPERATOR POSITION. (See diagram above.) Other positions are unsafe because they can increase the risk of injury from crushing, cutting, flying objects, or burns.

•Remove hands. Remove both hands from log before activating Split Control Lever.

•Hand activate. Use only your hand to operate the Split Control Lever. Never use any other body part, or a rope, cable, or other remote device to actuate the control.

•Second person. Many accidents occur when there is more than one person involved in loading and operating the log splitter. Only one person should operate the controls. If a second person is assisting in loading logs, the operator must NEVER actuate the Split Control Lever until the assistant and all bystanders are at least 10 feet away. NEVER allow an assistant to hold the log in place while the operator actuates the Split Control Lever.

Release Split Control Lever to stop wedge movement when log is split.

WARNING: Cracks in logs can close quickly and pinch fingers. Keep fingers away from any cracks that open in partially split logs.

SPLIT CONTROL LEVER OPERATION

If a log does not split completely and becomes stuck on the wedge, follow the instructions below to remove the log.

A log can become stuck to the wedge if the wedge becomes embedded in the log and the log doesn’t split and separate. This can happen if the log is too stringy or tough to split completely. A stuck log will move back with the wedge on the initial attempt to retract the wedge. If this happens, retract the wedge completely to allow the splitter to strip the log from the wedge. Keep hands clear of log and wedge while wedge is retracting.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents M1108D Hazard Signal Word Definitions Table of Contents Warranty Registration About Your Log SplitterThis equipment to others About Your Log SplitterSafety Label Locations Split Control Lever Operation Machine Component Identification DescriptionInitial Set-Up Wear between the keepers and beam Way Wedge Wings Wing Assembly Optional 4-Way Wedge WingsMoving and Towing to the Job Site Moving the log splitterImportant Make sure log splitter engine is off Towing Put front outrigger legAttach log splitter to vehicle hitch Important safety instructions Before Each Use-Inspection / Maintenance Step One Inspect and maintain log splitter before each useRemove debris from engine, muffler, and moving parts Check fuel tank and fuel lines for leaksHydraulic system Check the hydraulic system carefully Before Each Use-Inspection / Maintenance Before Each Use Fueling Remove gas cap Remove engine gas capAdd gasoline Fire precautions Before Each Use Work Site Selection & Set-UpStep Three Work site selection and log splitter set-up Select locationLock both outrigger legs Block wheels Apply greaseLock both the outrigger legs in the Down position General safety information Splitting OperationSet to HorizontalOr vertical ClothingLock rear outrigger leg in down position Vertical positionFingers or cause damage to the splitter Load log Correct Log OrientationExtend wedge Stop wedgeReturn wedge Remove split wood After useRemove split wood from area Turn off engine Remove engine debrisStorage Short-Term StoragePeriodic Maintenance As specified in spark arrestor muffler manual Troubleshooting Any Questions, Comments, Problems or Parts OrdersSpecifications Parts Breakdown Exploded View 1108, 1109, 1114 Rev D ALL Summary of Important Safety Information for Operation Safety Before Use Read/instruct Safety During Inspection/MaintenancePersonal protective equipment Safety During Fueling Safety in Work Site SelectionSafety During Use General Safety During Use Safety in Loading, Operating, and UnloadingLoading/Unloading Safety After use Assembly Instructions Assembly Instructions Step Bolt Catch Pin Towbar Outrigger Leg Fasten Horizontal Beam Lock to 1114 models only Tighten Idle Control Bolts to 20 lb- ft with a wrench Return Line

M1108D specifications

The North Star M1108D is a versatile and advanced military vehicle designed to meet the rigorous demands of modern warfare. Known for its robustness and adaptability, the M1108D has been developed with state-of-the-art technologies and features that enhance its performance in diverse environments.

One of the standout features of the M1108D is its powerful drivetrain, equipped with a dependable turbocharged engine that delivers impressive horsepower and torque. This ensures the vehicle can traverse challenging terrains, whether urban landscapes or rugged off-road conditions, making it a reliable option for military operations.

The M1108D boasts an independent suspension system, providing excellent ride quality and stability, especially when navigating difficult ground surfaces. This system allows for improved handling, reducing the wear and tear on the vehicle while enhancing crew comfort during long missions.

In terms of protection, the vehicle is designed with advanced armor plating that offers a high level of ballistic and blast protection for its occupants. This ensures that personnel inside can operate with greater confidence, knowing they are shielded from potential threats. Additionally, the M1108D is equipped with upgraded defensive technologies such as smoke grenade launchers and jamming systems, further enhancing its survivability on the battlefield.

Another critical characteristic of the M1108D is its modular design, allowing for easy customization and adaptation. It can be configured for various roles, including troop transport, command and control, medical evacuation, or as a platform for weapon systems. This versatility makes it an ideal choice for diverse military operations.

The vehicle also integrates modern communication and navigation technologies, facilitating real-time coordination and situational awareness. These systems enhance operational effectiveness, allowing units to respond quickly and efficiently to evolving battlefield conditions.

Fuel efficiency is an essential aspect of the M1108D, as its engineering incorporates features that optimize consumption without compromising performance. This attribute extends operational range, ensuring that missions can be conducted with fewer logistical challenges.

Overall, the North Star M1108D exemplifies modern military vehicle design, combining durability, versatility, and advanced technological integration. Its myriad features make it a vital asset for armed forces, capable of adapting to the unpredictable nature of contemporary combat scenarios. As militaries around the world continue to evolve, the M1108D stands out as a reliable and effective solution for a range of operational needs.
Top Page Image Contents