North Star M1108D owner manual Safety Before Use Read/instruct, Personal protective equipment

Page 34

Summary of Important Safety Information for Operation

●Tires. Be sure the tires are fully inflated and in good repair before towing the log splitter. When adding air to the tires, do not over-inflate – serious injury could occur if tire explodes.

●Added length. Be aware of the added length of the splitter.

●Speed Limit. Never tow this log splitter over 45 mph. Faster speeds may result in loss of control.

●Rough terrain. Be extra cautious and drive slowly when traveling over rough terrain.

●Under the influence. Never tow this splitter while under the influence of alcohol, drugs, or medication.

●On public roads. If towing on a public road, make sure to comply with all local, state, and federal towing requirements. It is the sole responsibility of the purchaser to obtain licensing, trailer lights, safety chains or signage, as needed to comply.

●Unattended. Turn off the towing vehicle before leaving the splitter unattended.

●Disconnect before operate. Do not use the log splitter while it is connected to the towing vehicle.

Safety – Before Use

Read/instruct

●Read manual. Do not allow anyone to operate the log splitter who has not read the owner’s manual or has not been instructed on the safe use of the splitter.

●Review safety rules. Before starting this log splitter, review the “Rules for Safe operation.” Failure to follow these rules may result in serious injury to the operator or bystanders.

●Know how to stop. Be thoroughly familiar with all controls and proper use of the equipment. Know how to stop the splitter and relieve system pressures quickly if needed.

Personal protective equipment

●Eye protection. Always wear safety glasses or goggles when operating the machine. Pieces of log may fly out and serious eye injury can occur.

●Boots. Falling logs can crush feet. Always wear safety shoes or heavy boots when operating or helping to load logs.

●Loose/dangling. Loose or dangling apparel can become entangled in moving parts. Never wear jewelry or loose- fitting clothing.

●Gloves. Wear snug fitting gloves without draw strings or loose cuffs.

●Hearing Protection. The use of ear plugs or other hearing protection device is recommended.

Safety During Inspection/Maintenance

Always inspect your log splitter before each use, and repair as needed, to keep it in safe working condition:

●Engine off. Always make sure the engine is off before cleaning, repairing or adjusting the splitter, except as recommended by the manufacturer.

●Engine debris. Debris on a hot engine can be a fire hazard. With the engine off, clean debris and chaff from engine cylinder head, cylinder head fins, blower housing rotating screen, and muffler areas. Avoid contact with hot muffler.

●Other debris. Debris on moving parts can cause excess wear. With the splitter engine off, clear debris from moving parts.

●Fuel tank / lines. Before each use, check fuel tank and fuel lines for leaks. Any fuel leak is a fire hazard. Fix any fuel leaks before starting engine.

●Mechanical parts. Check to be sure that all nuts and bolts are tight to make sure the log splitter is in safe working condition.

●Hydraulic system. Check the hydraulic system (hoses, tubing, clamps/fittings, pump, and cylinder) carefully before each use. Do not operate the log splitter with frayed, kinked, cracked or damaged hydraulic hoses, fittings, or tubing, or if oily residue is observed on any of the components. High fluid pressures and temperatures are developed in the log splitter. Hydraulic fluid escaping through a pin hole sized opening can burn or puncture skin, resulting in wounds that could cause blood poisoning, infection, disability, gangrene, amputation, or death. Therefore, the following instructions should be heeded at all times when inspecting or servicing the hydraulic components of the log splitter: o Do not remove the hydraulic oil dipstick when the engine is running. Hot oil can escape causing severe burns.

Allow log splitter to cool completely before removing hydraulic oil dipstick. o Do not adjust the pressure setting of the pump or valve.

o Do not check for leaks with your hand. Leaks can be located by holding a piece of cardboard or wood (at least two feet long) with your hand at one end and passing the other end over the suspected area (wear eye protection). Look for discoloration of the cardboard or wood.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents M1108D Hazard Signal Word Definitions Table of Contents This equipment to others Warranty RegistrationAbout Your Log Splitter About Your Log SplitterSafety Label Locations Split Control Lever Operation Machine Component Identification DescriptionInitial Set-Up Wear between the keepers and beam Way Wedge Wings Wing Assembly Optional 4-Way Wedge WingsMoving the log splitter Moving and Towing to the Job SiteImportant Make sure log splitter engine is off Put front outrigger leg TowingAttach log splitter to vehicle hitch Important safety instructions Remove debris from engine, muffler, and moving parts Before Each Use-Inspection / MaintenanceStep One Inspect and maintain log splitter before each use Check fuel tank and fuel lines for leaksHydraulic system Check the hydraulic system carefully Before Each Use-Inspection / Maintenance Remove gas cap Remove engine gas cap Before Each Use FuelingAdd gasoline Step Three Work site selection and log splitter set-up Fire precautionsBefore Each Use Work Site Selection & Set-Up Select locationBlock wheels Apply grease Lock both outrigger legsLock both the outrigger legs in the Down position General safety information Splitting OperationOr vertical Set toHorizontal ClothingVertical position Lock rear outrigger leg in down positionFingers or cause damage to the splitter Load log Correct Log OrientationExtend wedge Stop wedgeRemove split wood from area Return wedgeRemove split wood After use Turn off engine Remove engine debrisStorage Short-Term StoragePeriodic Maintenance As specified in spark arrestor muffler manual Troubleshooting Any Questions, Comments, Problems or Parts OrdersSpecifications Parts Breakdown Exploded View 1108, 1109, 1114 Rev D ALL Summary of Important Safety Information for Operation Safety During Inspection/Maintenance Safety Before Use Read/instructPersonal protective equipment Safety During Fueling Safety in Work Site SelectionSafety in Loading, Operating, and Unloading Safety During Use General Safety During UseLoading/Unloading Safety After use Assembly Instructions Assembly Instructions Step Bolt Catch Pin Towbar Outrigger Leg Fasten Horizontal Beam Lock to 1114 models only Tighten Idle Control Bolts to 20 lb- ft with a wrench Return Line

M1108D specifications

The North Star M1108D is a versatile and advanced military vehicle designed to meet the rigorous demands of modern warfare. Known for its robustness and adaptability, the M1108D has been developed with state-of-the-art technologies and features that enhance its performance in diverse environments.

One of the standout features of the M1108D is its powerful drivetrain, equipped with a dependable turbocharged engine that delivers impressive horsepower and torque. This ensures the vehicle can traverse challenging terrains, whether urban landscapes or rugged off-road conditions, making it a reliable option for military operations.

The M1108D boasts an independent suspension system, providing excellent ride quality and stability, especially when navigating difficult ground surfaces. This system allows for improved handling, reducing the wear and tear on the vehicle while enhancing crew comfort during long missions.

In terms of protection, the vehicle is designed with advanced armor plating that offers a high level of ballistic and blast protection for its occupants. This ensures that personnel inside can operate with greater confidence, knowing they are shielded from potential threats. Additionally, the M1108D is equipped with upgraded defensive technologies such as smoke grenade launchers and jamming systems, further enhancing its survivability on the battlefield.

Another critical characteristic of the M1108D is its modular design, allowing for easy customization and adaptation. It can be configured for various roles, including troop transport, command and control, medical evacuation, or as a platform for weapon systems. This versatility makes it an ideal choice for diverse military operations.

The vehicle also integrates modern communication and navigation technologies, facilitating real-time coordination and situational awareness. These systems enhance operational effectiveness, allowing units to respond quickly and efficiently to evolving battlefield conditions.

Fuel efficiency is an essential aspect of the M1108D, as its engineering incorporates features that optimize consumption without compromising performance. This attribute extends operational range, ensuring that missions can be conducted with fewer logistical challenges.

Overall, the North Star M1108D exemplifies modern military vehicle design, combining durability, versatility, and advanced technological integration. Its myriad features make it a vital asset for armed forces, capable of adapting to the unpredictable nature of contemporary combat scenarios. As militaries around the world continue to evolve, the M1108D stands out as a reliable and effective solution for a range of operational needs.
Top Page Image Contents