North Star M1108D owner manual Safety After use

Page 37

Summary of Important Safety Information for Operation

•NOTE for vertical position loading: Place the log on the endplate and turn it until it leans against the beam and is stable. If the log is too big or oddly shaped, stabilize the log with wooden shims between the log and endplate or ground. DO NOT use your leg or knee to stabilize the log. NEVER stabilize the log by placing your hand on top of the log.

•Wedge moving. NEVER load or unload logs while the wedge is moving.

•Cracks. Cracks in logs can close quickly and pinch fingers. Keep fingers away from any cracks that open in partially split logs.

•Split log pile. Move each log away from log splitter after it is split. Split logs left near the log splitter are a trip hazard.

•Remove hands. Remove both hands from log before activating Split Control Lever.

•Hand activate. Use only your hand to operate the Split Control Lever. Never use any other body part, or a rope, cable, or other remote device to actuate the control.

•Returning wedge. Once the control valve is actuated in the return direction, the wedge is designed to keep returning by itself completely and then stop automatically. Stay clear while the wedge is returning. It is still powerful enough on the return stroke to cause serious injury.

•Log stuck on wedge. If a log does not split completely and becomes stuck on the wedge, follow the instructions below to remove the log. A log can become stuck to the wedge if the wedge becomes embedded in the log and the log doesn’t split and separate. This can happen if the log is too stringy or tough to split completely. A stuck log will move back with the wedge on the initial attempt to retract the wedge. If this happens, retract the wedge completely to allow the splitter to strip the log from the wedge. Keep hands clear of log and wedge while wedge is retracting.

WARNING: NEVER attempt to remove a stuck log by:

•Modifying the splitter.

•Adding attachments to the splitter.

Personal injury could result from log or metal pieces flying out at high speed toward the operator or bystanders, or the splitter could become damaged.

•Changing splitting position. Do not change splitting positions (horizontal/vertical) with the engine running. You may contact the muffler and receive serious burns. Be careful to avoid contact with hot muffler even after the engine is turned off.

•Refueling. Never refuel the engine until it has cooled at least two minutes.

Safety – After use

•Return to horizontal. If in the vertical position, turn off engine and return log splitter to the horizontal position for greater stability and to prepare for transportation. Avoid contact with hot muffler.

•Remove engine debris. Debris on a hot engine can be a fire hazard. With the engine off, clean debris and chaff from engine cylinder head, cylinder head fins, blower housing rotating screen, and muffler areas. Avoid contact with hot muffler.

•Let engine cool before storing. Let engine cool for at least five minutes before storing. A hot engine can be a fire hazard.

•Storage location. Store the log splitter in a location away from sources of heat, open flames, sparks or pilot lights – such as water heaters, space heaters, furnaces, clothes dryers, or other gas appliances. Even if the log splitter’s gas tank is empty, residual gasoline vapors could ignite.

•Gasoline storage. Store extra gasoline in a cool, dry place in an UL approved, tightly sealed container. Gasoline vapors can ignite if they collect inside an enclosure.

•Periodic maintenance. Perform periodic maintenance as directed in this manual to keep the log splitter in safe working condition.

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents M1108D Hazard Signal Word Definitions Table of Contents About Your Log Splitter Warranty RegistrationThis equipment to others About Your Log SplitterSafety Label Locations Split Control Lever Operation Description Machine Component IdentificationInitial Set-Up Wear between the keepers and beam Optional 4-Way Wedge Wings Way Wedge Wings Wing AssemblyMoving the log splitter Moving and Towing to the Job SiteImportant Make sure log splitter engine is off Put front outrigger leg TowingAttach log splitter to vehicle hitch Important safety instructions Step One Inspect and maintain log splitter before each use Before Each Use-Inspection / MaintenanceRemove debris from engine, muffler, and moving parts Check fuel tank and fuel lines for leaksHydraulic system Check the hydraulic system carefully Before Each Use-Inspection / Maintenance Remove gas cap Remove engine gas cap Before Each Use FuelingAdd gasoline Before Each Use Work Site Selection & Set-Up Fire precautionsStep Three Work site selection and log splitter set-up Select locationBlock wheels Apply grease Lock both outrigger legsLock both the outrigger legs in the Down position Splitting Operation General safety informationHorizontal Set toOr vertical ClothingVertical position Lock rear outrigger leg in down positionFingers or cause damage to the splitter Correct Log Orientation Load logStop wedge Extend wedgeRemove split wood After use Return wedgeRemove split wood from area Turn off engine Remove engine debrisShort-Term Storage StoragePeriodic Maintenance As specified in spark arrestor muffler manual Any Questions, Comments, Problems or Parts Orders TroubleshootingSpecifications Parts Breakdown Exploded View 1108, 1109, 1114 Rev D ALL Summary of Important Safety Information for Operation Safety During Inspection/Maintenance Safety Before Use Read/instructPersonal protective equipment Safety in Work Site Selection Safety During FuelingSafety in Loading, Operating, and Unloading Safety During Use General Safety During UseLoading/Unloading Safety After use Assembly Instructions Assembly Instructions Step Bolt Catch Pin Towbar Outrigger Leg Fasten Horizontal Beam Lock to 1114 models only Tighten Idle Control Bolts to 20 lb- ft with a wrench Return Line

M1108D specifications

The North Star M1108D is a versatile and advanced military vehicle designed to meet the rigorous demands of modern warfare. Known for its robustness and adaptability, the M1108D has been developed with state-of-the-art technologies and features that enhance its performance in diverse environments.

One of the standout features of the M1108D is its powerful drivetrain, equipped with a dependable turbocharged engine that delivers impressive horsepower and torque. This ensures the vehicle can traverse challenging terrains, whether urban landscapes or rugged off-road conditions, making it a reliable option for military operations.

The M1108D boasts an independent suspension system, providing excellent ride quality and stability, especially when navigating difficult ground surfaces. This system allows for improved handling, reducing the wear and tear on the vehicle while enhancing crew comfort during long missions.

In terms of protection, the vehicle is designed with advanced armor plating that offers a high level of ballistic and blast protection for its occupants. This ensures that personnel inside can operate with greater confidence, knowing they are shielded from potential threats. Additionally, the M1108D is equipped with upgraded defensive technologies such as smoke grenade launchers and jamming systems, further enhancing its survivability on the battlefield.

Another critical characteristic of the M1108D is its modular design, allowing for easy customization and adaptation. It can be configured for various roles, including troop transport, command and control, medical evacuation, or as a platform for weapon systems. This versatility makes it an ideal choice for diverse military operations.

The vehicle also integrates modern communication and navigation technologies, facilitating real-time coordination and situational awareness. These systems enhance operational effectiveness, allowing units to respond quickly and efficiently to evolving battlefield conditions.

Fuel efficiency is an essential aspect of the M1108D, as its engineering incorporates features that optimize consumption without compromising performance. This attribute extends operational range, ensuring that missions can be conducted with fewer logistical challenges.

Overall, the North Star M1108D exemplifies modern military vehicle design, combining durability, versatility, and advanced technological integration. Its myriad features make it a vital asset for armed forces, capable of adapting to the unpredictable nature of contemporary combat scenarios. As militaries around the world continue to evolve, the M1108D stands out as a reliable and effective solution for a range of operational needs.
Top Page Image Contents