North Star M1108D owner manual Set to, Horizontal, Or vertical, Clothing, Gear

Page 21

Splitting Operation

1. Put on

Wear the following protective clothing and safety gear:

protective

1)

Eye protection. Always wear safety glasses or goggles when operating the machine. Pieces

clothing /

 

of log may fly out and serious eye injury can occur.

gear

 

2)

Boots. Falling logs can crush feet. Always wear safety shoes or heavy boots when operating

 

 

 

or helping to load logs.

 

3)

Gloves. Wear snug fitting gloves without draw strings or loose cuffs.

 

4)

Hearing protection. The use of ear plugs or other hearing protection device is recommended.

 

5)

No Loose / dangling. Loose or dangling apparel can become entangled in moving parts.

 

 

Never wear jewelry or loose-fitting clothing.

2. Lock & block

Block the wheels to prevent unintended movement of the log splitter. Check that:

 

1) The outrigger legs are both locked in the DOWN position.

 

2) The wheels are blocked.

3. Set to

Set log splitter into either the horizontal or vertical splitting position

horizontal

The HORIZONTAL splitting position is used for lighter logs that can be easily loaded onto the beam.

or vertical:

The VERTICAL splitting position is used for light logs as well as heavy logs that are difficult to load

 

onto the beam.

 

Note:

 

Musculoskeletal injury can result from lifting logs onto the log splitter if proper lifting techniques

 

are not used or the logs are too heavy for a person’s size, weight, or strength. In some cases, logs

 

as small as 8” in diameter and 14” in length may be heavier than what some persons should be

 

repeatedly lifting onto the splitter.

 

The use of the vertical splitting position can greatly reduce the need to lift logs onto the splitter.

 

Employers are advised to consider NIOSH lifting guidelines when assigning employees to log

 

splitting tasks for an extended period of time.

 

WARNING: NEVER change splitting positions with the engine running. You may

 

contact the muffler and receive serious burns.

a)Set to Make sure beam is locked securely in the horizontal position by checking the horizontal lock. Horizontal Rear outrigger leg must be locked in horizontal splitting position.

position

Horizontal Splitting Position

Rear outrigger leg

Horizontal

 

Lock

Front outrigger leg

 

Fig 02412

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents M1108D Hazard Signal Word Definitions Table of Contents About Your Log Splitter Warranty RegistrationThis equipment to others About Your Log SplitterSafety Label Locations Split Control Lever Operation Description Machine Component IdentificationInitial Set-Up Wear between the keepers and beam Optional 4-Way Wedge Wings Way Wedge Wings Wing AssemblyMoving and Towing to the Job Site Moving the log splitterImportant Make sure log splitter engine is off Towing Put front outrigger legAttach log splitter to vehicle hitch Important safety instructions Step One Inspect and maintain log splitter before each use Before Each Use-Inspection / MaintenanceRemove debris from engine, muffler, and moving parts Check fuel tank and fuel lines for leaksHydraulic system Check the hydraulic system carefully Before Each Use-Inspection / Maintenance Before Each Use Fueling Remove gas cap Remove engine gas capAdd gasoline Before Each Use Work Site Selection & Set-Up Fire precautionsStep Three Work site selection and log splitter set-up Select locationLock both outrigger legs Block wheels Apply greaseLock both the outrigger legs in the Down position Splitting Operation General safety informationHorizontal Set toOr vertical ClothingLock rear outrigger leg in down position Vertical positionFingers or cause damage to the splitter Correct Log Orientation Load logStop wedge Extend wedgeRemove split wood After use Return wedgeRemove split wood from area Turn off engine Remove engine debrisShort-Term Storage StoragePeriodic Maintenance As specified in spark arrestor muffler manual Any Questions, Comments, Problems or Parts Orders TroubleshootingSpecifications Parts Breakdown Exploded View 1108, 1109, 1114 Rev D ALL Summary of Important Safety Information for Operation Safety Before Use Read/instruct Safety During Inspection/MaintenancePersonal protective equipment Safety in Work Site Selection Safety During FuelingSafety During Use General Safety During Use Safety in Loading, Operating, and UnloadingLoading/Unloading Safety After use Assembly Instructions Assembly Instructions Step Bolt Catch Pin Towbar Outrigger Leg Fasten Horizontal Beam Lock to 1114 models only Tighten Idle Control Bolts to 20 lb- ft with a wrench Return Line

M1108D specifications

The North Star M1108D is a versatile and advanced military vehicle designed to meet the rigorous demands of modern warfare. Known for its robustness and adaptability, the M1108D has been developed with state-of-the-art technologies and features that enhance its performance in diverse environments.

One of the standout features of the M1108D is its powerful drivetrain, equipped with a dependable turbocharged engine that delivers impressive horsepower and torque. This ensures the vehicle can traverse challenging terrains, whether urban landscapes or rugged off-road conditions, making it a reliable option for military operations.

The M1108D boasts an independent suspension system, providing excellent ride quality and stability, especially when navigating difficult ground surfaces. This system allows for improved handling, reducing the wear and tear on the vehicle while enhancing crew comfort during long missions.

In terms of protection, the vehicle is designed with advanced armor plating that offers a high level of ballistic and blast protection for its occupants. This ensures that personnel inside can operate with greater confidence, knowing they are shielded from potential threats. Additionally, the M1108D is equipped with upgraded defensive technologies such as smoke grenade launchers and jamming systems, further enhancing its survivability on the battlefield.

Another critical characteristic of the M1108D is its modular design, allowing for easy customization and adaptation. It can be configured for various roles, including troop transport, command and control, medical evacuation, or as a platform for weapon systems. This versatility makes it an ideal choice for diverse military operations.

The vehicle also integrates modern communication and navigation technologies, facilitating real-time coordination and situational awareness. These systems enhance operational effectiveness, allowing units to respond quickly and efficiently to evolving battlefield conditions.

Fuel efficiency is an essential aspect of the M1108D, as its engineering incorporates features that optimize consumption without compromising performance. This attribute extends operational range, ensuring that missions can be conducted with fewer logistical challenges.

Overall, the North Star M1108D exemplifies modern military vehicle design, combining durability, versatility, and advanced technological integration. Its myriad features make it a vital asset for armed forces, capable of adapting to the unpredictable nature of contemporary combat scenarios. As militaries around the world continue to evolve, the M1108D stands out as a reliable and effective solution for a range of operational needs.
Top Page Image Contents