North Star M1108D owner manual Periodic Maintenance

Page 27

Periodic Maintenance

In addition to the maintenance performed with each use, periodic maintenance should also be performed according to the following schedule.

WARNING

ALWAYS shut off the engine, disconnect the spark plug, and relieve system pressure before cleaning, adjusting, or repairing the splitter. Relieve system pressure by moving Split Control Lever back and forth several times.

IMPORTANT:

If a part needs replacement only use parts that meets the manufacturer’s specifications. Replacement parts that do not meet specifications may result in a safety hazard or poor operation of the log splitter.

1.

Engine

As specified in engine

 

maintenance

manual

 

 

 

2.

Hydraulic Oil

Annually /

 

Change

100 hours

 

 

 

Perform engine maintenance as specified in engine owner’s manual.

Change Hydraulic Oil.

WARNING: High fluid pressures and temperatures are developed in hydraulic log splitters. Hydraulic fluid escaping through a pin hole sized opening can burn or puncture skin, resulting in wounds that could cause blood poisoning, infection, disability, gangrene, amputation, or death. Therefore, the following instructions should be heeded at all times when inspecting or servicing the hydraulic components of the log splitter.

•NEVER check for leaks with your hand. Leaks can be located by holding a piece of cardboard or wood (at least two feet long) with your hand at one end and passing the other end over the suspected area (wear eye protection). Look for discoloration of the cardboard or wood.

•NEVER adjust the pressure of the pump or valve.

•If injured by escaping fluid, no matter how small the wound is, see a doctor at once. A typical injection injury may be a small wound that does not look serious. However, severe infection or reaction can result if proper medical treatment is not administered immediately by a doctor who is familiar with injection injuries.

1.Use 10wt AW32, ASLE H-150, or ISO32 oil.

2.Relieve hydraulic system pressure by moving Split Control Lever back and forth several times.

3.Remove hydraulic oil dipstick.

WARNING: NEVER remove the hydraulic oil dipstick when the engine is running or hot. Hot oil can escape causing severe burns. Allow the log splitter to cool completely before removing hydraulic oil dipstick.

4.Remove the drain plug from the hydraulic tank to drain the hydraulic oil into a 10 gallon pan.

5.Remove suction strainer and wipe of debris with a dry cloth.

6.Fill the hydraulic tank with wedge retracted.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents M1108D Hazard Signal Word Definitions Table of Contents About Your Log Splitter Warranty RegistrationAbout Your Log Splitter This equipment to othersSafety Label Locations Split Control Lever Operation Description Machine Component IdentificationInitial Set-Up Wear between the keepers and beam Optional 4-Way Wedge Wings Way Wedge Wings Wing AssemblyMoving and Towing to the Job Site Moving the log splitterImportant Make sure log splitter engine is off Towing Put front outrigger legAttach log splitter to vehicle hitch Important safety instructions Check fuel tank and fuel lines for leaks Before Each Use-Inspection / MaintenanceStep One Inspect and maintain log splitter before each use Remove debris from engine, muffler, and moving partsHydraulic system Check the hydraulic system carefully Before Each Use-Inspection / Maintenance Before Each Use Fueling Remove gas cap Remove engine gas capAdd gasoline Select location Fire precautionsBefore Each Use Work Site Selection & Set-Up Step Three Work site selection and log splitter set-upLock both outrigger legs Block wheels Apply greaseLock both the outrigger legs in the Down position Splitting Operation General safety informationClothing Set toHorizontal Or verticalLock rear outrigger leg in down position Vertical positionFingers or cause damage to the splitter Correct Log Orientation Load logStop wedge Extend wedgeTurn off engine Remove engine debris Return wedgeRemove split wood After use Remove split wood from areaShort-Term Storage StoragePeriodic Maintenance As specified in spark arrestor muffler manual Any Questions, Comments, Problems or Parts Orders TroubleshootingSpecifications Parts Breakdown Exploded View 1108, 1109, 1114 Rev D ALL Summary of Important Safety Information for Operation Safety Before Use Read/instruct Safety During Inspection/MaintenancePersonal protective equipment Safety in Work Site Selection Safety During FuelingSafety During Use General Safety During Use Safety in Loading, Operating, and UnloadingLoading/Unloading Safety After use Assembly Instructions Assembly Instructions Step Bolt Catch Pin Towbar Outrigger Leg Fasten Horizontal Beam Lock to 1114 models only Tighten Idle Control Bolts to 20 lb- ft with a wrench Return Line

M1108D specifications

The North Star M1108D is a versatile and advanced military vehicle designed to meet the rigorous demands of modern warfare. Known for its robustness and adaptability, the M1108D has been developed with state-of-the-art technologies and features that enhance its performance in diverse environments.

One of the standout features of the M1108D is its powerful drivetrain, equipped with a dependable turbocharged engine that delivers impressive horsepower and torque. This ensures the vehicle can traverse challenging terrains, whether urban landscapes or rugged off-road conditions, making it a reliable option for military operations.

The M1108D boasts an independent suspension system, providing excellent ride quality and stability, especially when navigating difficult ground surfaces. This system allows for improved handling, reducing the wear and tear on the vehicle while enhancing crew comfort during long missions.

In terms of protection, the vehicle is designed with advanced armor plating that offers a high level of ballistic and blast protection for its occupants. This ensures that personnel inside can operate with greater confidence, knowing they are shielded from potential threats. Additionally, the M1108D is equipped with upgraded defensive technologies such as smoke grenade launchers and jamming systems, further enhancing its survivability on the battlefield.

Another critical characteristic of the M1108D is its modular design, allowing for easy customization and adaptation. It can be configured for various roles, including troop transport, command and control, medical evacuation, or as a platform for weapon systems. This versatility makes it an ideal choice for diverse military operations.

The vehicle also integrates modern communication and navigation technologies, facilitating real-time coordination and situational awareness. These systems enhance operational effectiveness, allowing units to respond quickly and efficiently to evolving battlefield conditions.

Fuel efficiency is an essential aspect of the M1108D, as its engineering incorporates features that optimize consumption without compromising performance. This attribute extends operational range, ensuring that missions can be conducted with fewer logistical challenges.

Overall, the North Star M1108D exemplifies modern military vehicle design, combining durability, versatility, and advanced technological integration. Its myriad features make it a vital asset for armed forces, capable of adapting to the unpredictable nature of contemporary combat scenarios. As militaries around the world continue to evolve, the M1108D stands out as a reliable and effective solution for a range of operational needs.
Top Page Image Contents