North Star M1108D owner manual Step

Page 40

Assembly Instructions

Step 1

Remove shipping crate

If there are rubber boots on the axles, remove and discard them

Slide Wheel onto Axle with Valve Stem facing out

Slide Outer Bearing onto Axle (outer bearing may be shipped loose in parts bag or loose inside wheel)

Outer bearing taper points into log splitter Slide Wheel Washer onto Axle

Axle with the

Outer Rubber Boot

Bearingremoved

Wheel

Washer

Axle Nut

Wheel

Cotter
	Valve Stem Out
Pin

Step 2

Thread Axle Nut onto Axle (hand tight) Back Axle Nut off ¼ turn

Make sure Wheel spins freely

Insert Cotter Pin through hole in Axle and bend it so Axle Nut cannot come off

Make sure Wheel spins freely

Tap Dust Cap onto Wheel with a soft faced mallet

Repeat steps 1 and 2 for the other Wheel

Step 3

Connect Towbar to Axle/Tank using (2) Tank Bolts and (2) Tank nuts (already in place)

Tighten Bolts to 90 lb-ft with a wrench

Wheel

Axle Nut

Dust Cap

Cotter Pin

Bolt

Axle/Tank

Towbar

Fig 02417

Image 40

Contents M1108D Hazard Signal Word Definitions Table of Contents Warranty Registration About Your Log SplitterThis equipment to others About Your Log SplitterSafety Label Locations Split Control Lever Operation Machine Component Identification DescriptionInitial Set-Up Wear between the keepers and beam Way Wedge Wings Wing Assembly Optional 4-Way Wedge WingsMoving the log splitter Moving and Towing to the Job SiteImportant Make sure log splitter engine is off Put front outrigger leg TowingAttach log splitter to vehicle hitch Important safety instructions Before Each Use-Inspection / Maintenance Step One Inspect and maintain log splitter before each useRemove debris from engine, muffler, and moving parts Check fuel tank and fuel lines for leaksHydraulic system Check the hydraulic system carefully Before Each Use-Inspection / Maintenance Remove gas cap Remove engine gas cap Before Each Use FuelingAdd gasoline Fire precautions Before Each Use Work Site Selection & Set-UpStep Three Work site selection and log splitter set-up Select locationBlock wheels Apply grease Lock both outrigger legsLock both the outrigger legs in the Down position General safety information Splitting OperationSet to HorizontalOr vertical ClothingVertical position Lock rear outrigger leg in down positionFingers or cause damage to the splitter Load log Correct Log OrientationExtend wedge Stop wedgeReturn wedge Remove split wood After useRemove split wood from area Turn off engine Remove engine debrisStorage Short-Term StoragePeriodic Maintenance As specified in spark arrestor muffler manual Troubleshooting Any Questions, Comments, Problems or Parts OrdersSpecifications Parts Breakdown Exploded View 1108, 1109, 1114 Rev D ALL Summary of Important Safety Information for Operation Safety During Inspection/Maintenance Safety Before Use Read/instructPersonal protective equipment Safety During Fueling Safety in Work Site SelectionSafety in Loading, Operating, and Unloading Safety During Use General Safety During UseLoading/Unloading Safety After use Assembly Instructions Assembly Instructions Step Bolt Catch Pin Towbar Outrigger Leg Fasten Horizontal Beam Lock to 1114 models only Tighten Idle Control Bolts to 20 lb- ft with a wrench Return Line

M1108D specifications

The North Star M1108D is a versatile and advanced military vehicle designed to meet the rigorous demands of modern warfare. Known for its robustness and adaptability, the M1108D has been developed with state-of-the-art technologies and features that enhance its performance in diverse environments.

One of the standout features of the M1108D is its powerful drivetrain, equipped with a dependable turbocharged engine that delivers impressive horsepower and torque. This ensures the vehicle can traverse challenging terrains, whether urban landscapes or rugged off-road conditions, making it a reliable option for military operations.

The M1108D boasts an independent suspension system, providing excellent ride quality and stability, especially when navigating difficult ground surfaces. This system allows for improved handling, reducing the wear and tear on the vehicle while enhancing crew comfort during long missions.

In terms of protection, the vehicle is designed with advanced armor plating that offers a high level of ballistic and blast protection for its occupants. This ensures that personnel inside can operate with greater confidence, knowing they are shielded from potential threats. Additionally, the M1108D is equipped with upgraded defensive technologies such as smoke grenade launchers and jamming systems, further enhancing its survivability on the battlefield.

Another critical characteristic of the M1108D is its modular design, allowing for easy customization and adaptation. It can be configured for various roles, including troop transport, command and control, medical evacuation, or as a platform for weapon systems. This versatility makes it an ideal choice for diverse military operations.

The vehicle also integrates modern communication and navigation technologies, facilitating real-time coordination and situational awareness. These systems enhance operational effectiveness, allowing units to respond quickly and efficiently to evolving battlefield conditions.

Fuel efficiency is an essential aspect of the M1108D, as its engineering incorporates features that optimize consumption without compromising performance. This attribute extends operational range, ensuring that missions can be conducted with fewer logistical challenges.

Overall, the North Star M1108D exemplifies modern military vehicle design, combining durability, versatility, and advanced technological integration. Its myriad features make it a vital asset for armed forces, capable of adapting to the unpredictable nature of contemporary combat scenarios. As militaries around the world continue to evolve, the M1108D stands out as a reliable and effective solution for a range of operational needs.