MTD OHD 190-180 warranty Attaching Support Bracket Bracket Assembly, Assembling Support Brackets

Page 7
Assembling Support

Clevis Pin

Figure 9

Outer holes

Figure 10

Figure 11

Model Series 650 through 699Upper Hole

Figure 12

Assembling Support

Brackets

Model Series 650 through 699

IMPORTANT: Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake.

1.Remove the top four self-tapping screws from the rear of the lawn tractor. See Figure 7 on the previous page.

2.Place the right hand grass catcher support bracket (F1 from Figure 4), in position, with the wide end on top and the narrow end pointing down as shown in Figure 8.

3.Secure the support bracket to the tractor frame with two self-tapping screws earlier removed. Refer to Figure 8. Repeat on the other side using part F2 from Figure 4.

NOTE: If the grass collection system is removed for any reason, it is not necessary to remove the support brackets from the tractor.

4.Insert a shoulder bolt (C in Figure 4) through a bell washer, (B in Figure 4) and insert the bolt from the outside of the bracket through the outer hole on the support bracket. Secure with a nut (A in Figure 4).

See Figure 8 for details. Repeat on other side.

NOTE: The reference above to “the outer hole” means the hole furthest away from the frame.

Attaching Bracket

Assembly

Model Series 650 through 699

1.Remove the two nuts and bolts on each side of the mounting bracket holding the hitch plate.

2.Rotate the hitch plate 180° from its original position. Re-insert the four bolts through mounting bracket and hitch plate frame and secure with nuts removed earlier. Use the outer holes (furthest from the mount- ing hooks) on the mounting bracket. See Figure 10.

3.For convenience, pivot the seat forward and leave it in that position until the grass collector is fully mounted and assembled.

4.Remove the hairpin clip and clevis pin from the rear of the mounting bracket assembly. See Figure 9.

5.Position the hooked ends of the mounting bracket assembly to the outside of the support brackets and over the shoulder bolts just installed on both sides of the tractor frame. See Figure 11.

6.Reinsert the clevis pin through the aligned holes in both the bracket assembly and the hitch plate and secure with the hairpin clip removed earlier. See Figure 12 for reference.

IMPORTANT: There are two holes in the clevis pin. Be sure to insert the hairpin clip in the upper hole to properly secure the bracket assembly to the hitch plate.

NOTE: For some tractor models, this clevis pin is too large. Use a smaller clevis pin (E in Figure 4) in

3

Attaching

Support

Bracket &

Bracket

Assembly

Model Series 650

through 699

IMPORTANT:

Before assembly, place

the tractor on a firm,

level surface, disengage the PTO, turn off tractor engine and set the park- ing brake.

NOTE:

If the grass collection system is removed for any reason, it is not necessary to remove the support brackets from the tractor.

IMPORTANT:

There are two holes in the clevis pin. Be sure to insert the hairpin clip in the upper hole to properly secure the bracket assembly to the hitch plate.

NOTE:

For some tractor

models, this clevis

pin is too large. Use a smaller clevis pin in its place with the same hairpin clip.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Twin Rear Bagger Kit READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATIONOPERATOR’S MANUAL To The Owner Carton Contents Assembly Parts Lists WarrantyBEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENT TABLE OF CONTENTSFinding and Recording Model Number Customer SupportSample Model Number FastAttach Twin Bag Grass CollectorDetermine The Model of Your Rider Rider Model IdentificationOne Chute Tube Carton ContentsCONTENTS OF CARTON toll free at# = Quantity CONTENTS OF HARDWARE PACKRH = Right Hand LH = Left Hand Before assembly, place the tractor on a firm Attaching Bracket AssemblyAttaching The Bracket Assembly Model Series 600 throughModel Series 650 through Attaching Support Bracket Bracket AssemblyAttaching Bracket Assembly Assembling Support BracketsInner Hole Model SeriesSelf tap screwsAll Model Series Attaching Grass Bags & Grass Bag CoverAttaching Grass Bags Grass Bag Cover 600 throughOn Older Model Riders Attaching Discharge ChuteDischarge Chute set the parking brake Bagger UsageAll Model Series All Models - 600 throughRear Twin Bagger For parts and/or accessories please callPart List Discharge Chute 38”/42” Bag Grass catcher Cover AssemblyPART NUMBER Hex Flange Lock Nut, 1/4-20MANUFACTURER’S LIMITED WARRANTY FOR IMPORTANTE Kit de embolsado posterior dobleModelos OHD-190-180 MANUAL DEL OPERADORANTES DE COMENZAR A MONTAR SU NUEVO EQUIPO Búsqueda y registro del número de modeloAsistencia al cliente ÍNDICEFastAttach con sistema de bolsa doble Identificación del modelo de podadora tractor Determine el modelo de la podadora tractorCONTENIDO DE LA CAJA Contenido de la cajaUn tubo de canal Un conjunto de canal de descarga CONTENIDO DEL PAQUETE DE ELEMENTOS DE FERRETERÍA Modelos series 650 a 699 inclusive Instalación Conjunto de soporteInstalación Conjunto de soporte Modelos series 600 a inclusiveEnsamblado de los soportes y del conjunto del soporteInstalación del soporte Instalación del conjunto del soporteVea la Figura Instalación del soporte y del con- junto del so- porteEnsamblado de los soportes Modelo Seriede pasto gire sobre el tubo de soporte y se abra Figura series 600 a inclusiveTodos los modelos Figura Figura FiguraFigura AB Figura Canal de descarga Figura Instalación del canal de descargaEn tractores de modelos más antiguos Todos los modelos series 600 a 699 inclusive NOTATira de retención Pasador de la tolva para recorte de césped Figura Uso de la embolsadoraTodas las series de modelos Todos los modelos - 600 a inclusiveLista de piezas Embolsa dora doble posteriorPara piezas y/o accesorios por favor llame al NÚMERO DE Para piezas y/oaccesorios por favor llame al 1-800-800- 7310-6483 ó al No. DEg. Gastos de transporte y llamadas por servicios técnicos GARANTÍA LIMITADA DEL FABRICANTE PARAEsta garantía limitada no lo cubrirá en los siguientes casos f. Piezas de reemplazo que no son piezas genuinas de MTDIMPRIMÉ AUX Collecteur arrière à deux sacsModèles OHD-190-180 MANUEL DE L’OPÉRATEURAVANT D’ASSEMBLER VOTRE NOUVEL ÉQUIPEMENT Pour trouver et enregistrer le numéro de modèleSupport client TABLE DES MATIERESDéterminer le modèle de votre tracteur Identificationdu modèle du tracteur Collecteur d’herbe à deux sacs FastAttachCONTENU DU CARTON Contenu du cartonPIÈCES DE QUINCAILLERIE Modèles de série 650 à Montage du support de fixationMontage du support de fixation Modèles de série 600 àModèle de série 650 à Montage dupalier sup- port et du support de fixation Montage des paliers supportsModèle de la série Modèle de la sérieVoir la Figure sacs à herbe et Montage des sacs à herbe et du couvercleMontage des du couvercleSur les anciens modèles de tracteurs Montage dela goulotte d’éjection Montage de la goulotte d’éjectionPatte de fixation Goupille du collecteur d’herbe Utilisation du collecteurTous les modèles Tous les modèles - Série 600 àà deux sacs CollecteurListe des pièces Palier support Collecteur NUMÉRO DEDESCRIPTION PIÈCEUtilisez cette page pour noter les informa tions importantes tions importantes Utilisez cette pagepour noter les informa f. Les pièces de rechange qui ne sont pas fabriquées par MTD GARANTIE LIMITÉE DU FABRICANTg. Les frais de transport et les appels de maintenance Cette garantie limitée ne s’applique pas dans les cas suivants
Top Page Image Contents