MTD OHD 190-180 Model Series, Attaching Support Bracket Bracket Assembly, Self tap, screws

Page 8

Model Series 700

3

Attaching

Support

Bracket &

Bracket

Assembly

Model Series 700

NOTE:

If the grass collection system is removed for any reason, it is not necessary to remove the support brackets from the tractor.

IMPORTANT:

There are two holes in the clevis pin. Be sure to insert the hairpin clip in the upper hole to properly secure the bracket assembly to the hitch plate.

Assembling Support

Brackets

Model Series 700

1.Locate the four self-tapping screws supplied in your hardware pack (D from Figure 4). Attach the right hand grass catcher support bracket (F1 from Figure 4) using two of the supplied screws in position

as shown in Figure 13. Place the left hand grass catcher support bracket (F2 from Figure 4) in position and secure with the other two screws.

5.Insert a shoulder bolt (C in Figure 4) through a bell washer, (B in Figure 4) and insert the bolt through the Inner hole (closest to the frame) on the outside of the support bracket. Secure with a nut (A in Figure 4). See Figure 13 for details. Repeat on other side.

NOTE: If the grass collection system is removed for any reason, it is not necessary to remove the support brackets from the tractor.

Attaching The Bracket

Assembly

1.Remove the two nuts and screws on each side of the mounting bracket holding the hitch plate.

See Figure 14.

2.Rotate the hitch plate 180° from its original position. Re-insert the four bolts through mounting bracket and hitch plate frame and secure with nuts removed earlier. Use the inner holes (closest to the mounting hooks) on the mounting bracket. Refer to Figure 15.

3.Remove the hairpin clip and clevis pin from the hitch plate as seen in Figure 14. Save the hardware.

4.Position the hooked ends of the mounting bracket assembly to the outside of the support bracket and over the shoulder bolts on both sides. Refer back to Figure 11 for reference.

5.Reinsert the clevis pin through the aligned holes in both the bracket assembly and the hitch plate and secure with the hairpin clip removed earlier. See Figure 16.

IMPORTANT: There are two holes in the clevis pin. Be sure to insert the hairpin clip in the upper hole to properly secure the bracket assembly to the hitch plate.

	Self tap	Support
	Self tap	Bracket
	screws	Bracket
	screws
	Inner Hole	Outside of Bracket

Figure 13

Clevis Pin

Figure 14

Inner holes

Figure 15

Upper Hole

Figure 16

8

Image 8

Contents READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION OPERATOR’S MANUALTo The Owner Carton Contents Assembly Parts Lists Warranty Twin Rear Bagger KitTABLE OF CONTENTS Finding and Recording Model NumberCustomer Support BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENTFastAttach Twin Bag Grass Collector Determine The Model of Your RiderRider Model Identiﬁcation Sample Model NumberCarton Contents CONTENTS OF CARTONtoll free at One Chute TubeRH = Right Hand LH = Left Hand CONTENTS OF HARDWARE PACK# = Quantity Attaching Bracket Assembly Attaching The Bracket AssemblyModel Series 600 through Before assembly, place the tractor on a firmAttaching Support Bracket Bracket Assembly Attaching Bracket AssemblyAssembling Support Brackets Model Series 650 throughModel Series Self tapscrews Inner HoleAttaching Grass Bags & Grass Bag Cover Attaching Grass Bags Grass Bag Cover600 through All Model SeriesDischarge Chute Attaching Discharge ChuteOn Older Model Riders Bagger Usage All Model SeriesAll Models - 600 through set the parking brakePart List For parts and/or accessories please callRear Twin Bagger Grass catcher Cover Assembly PART NUMBERHex Flange Lock Nut, 1/4-20 Discharge Chute 38”/42” BagMANUFACTURER’S LIMITED WARRANTY FOR Kit de embolsado posterior doble Modelos OHD-190-180MANUAL DEL OPERADOR IMPORTANTEBúsqueda y registro del número de modelo Asistencia al clienteÍNDICE ANTES DE COMENZAR A MONTAR SU NUEVO EQUIPOIdentiﬁ cación del modelo de podadora tractorDetermine el modelo de la podadora tractor FastAttach con sistema de bolsa dobleUn tubo de canal Un conjunto de canal de descarga Contenido de la cajaCONTENIDO DE LA CAJA CONTENIDO DEL PAQUETE DE ELEMENTOS DE FERRETERÍA Instalación Conjunto de soporte Instalación Conjunto de soporteModelos series 600 a inclusive Modelos series 650 a 699 inclusivey del conjunto del soporte Instalación del soporteInstalación del conjunto del soporte Ensamblado de los soportesInstalación del soporte y del con- junto del so- porte Ensamblado de los soportesModelo Serie Vea la Figuraseries 600 a inclusive Todos los modelosFigura Figura Figura de pasto gire sobre el tubo de soporte y se abra FiguraInstalación del canal de descarga En tractores de modelos más antiguosTodos los modelos series 600 a 699 inclusive NOTA Figura AB Figura Canal de descarga FiguraUso de la embolsadora Todas las series de modelosTodos los modelos - 600 a inclusive Tira de retención Pasador de la tolva para recorte de césped FiguraPara piezas y/o accesorios por favor llame al Embolsa dora doble posteriorLista de piezas Para piezas y/o accesorios por favor llame al 1-800-800- 7310-6483 ó alNo. DE NÚMERO DEGARANTÍA LIMITADA DEL FABRICANTE PARA Esta garantía limitada no lo cubrirá en los siguientes casosf. Piezas de reemplazo que no son piezas genuinas de MTD g. Gastos de transporte y llamadas por servicios técnicosCollecteur arrière à deux sacs Modèles OHD-190-180MANUEL DE L’OPÉRATEUR IMPRIMÉ AUXPour trouver et enregistrer le numéro de modèle Support clientTABLE DES MATIERES AVANT D’ASSEMBLER VOTRE NOUVEL ÉQUIPEMENTIdentiﬁcation du modèle du tracteurCollecteur d’herbe à deux sacs FastAttach Déterminer le modèle de votre tracteurContenu du carton CONTENU DU CARTONPIÈCES DE QUINCAILLERIE Montage du support de ﬁxation Montage du support de ﬁxationModèles de série 600 à Modèles de série 650 àMontage du palier sup- port et du support de ﬁxationMontage des paliers supports Modèle de série 650 àVoir la Figure Modèle de la sérieModèle de la série Montage des sacs à herbe et du couvercle Montage desdu couvercle sacs à herbe etMontage de la goulotte d’éjectionMontage de la goulotte d’éjection Sur les anciens modèles de tracteursUtilisation du collecteur Tous les modèlesTous les modèles - Série 600 à Patte de fixation Goupille du collecteur d’herbeListe des pièces Collecteurà deux sacs NUMÉRO DE DESCRIPTIONPIÈCE Palier support CollecteurUtilisez cette page pour noter les informa tions importantes pour noter les informa Utilisez cette pagetions importantes GARANTIE LIMITÉE DU FABRICANT g. Les frais de transport et les appels de maintenanceCette garantie limitée ne s’applique pas dans les cas suivants f. Les pièces de rechange qui ne sont pas fabriquées par MTD