MTD OHD 190-180 Attaching Grass Bags & Grass Bag Cover, Attaching Grass Bags Grass Bag Cover

Page 9

Attaching Grass Bags & Grass Bag Cover

Figure 17

Figure 18

Figure 19

Attaching Grass Bags & Grass Bag Cover

1.Place the support tube in position on the rear of unit by sliding the support tube down through the holes in the left side of the bracket assembly. Use the inside hole on the bracket assembly regardless of what size deck your tractor is equipped with. Refer to Figure 17.

2.Attach the grass bags by hooking them onto the grass bag bracket using the slots in the grass bag and the tabs on the grass bag bracket as shown in Figure 18.

3.Place the grass bag cover on top of the grass bags and align the holes on the hinges of the grass bag cover with the corresponding holes on the support tube assembly. See Figure 19.

4.Insert the clevis pin through the hinge on the support tube assembly and then through the grass bag cover. See Figure 20.

5.Secure with belleville washer and hairpin clip with the crown side of the washer going against the hairpin clip. See inset images in Figure 20.

6.Repeat with the second set of hardware through the second hinge of the grass bag and the tube assembly from the opposite direction.

NOTE: Insert the clevis pins from the outside in as shown in the inset images of Figure 20.

NOTE: It is very important to maintain this order and direction while installing these hardware pieces. After installation, make sure that the grass bag cover

pivots on the support tube and opens.

Figure 20

4

Attaching

Grass Bags

& Grass Bag

Cover

All Model Series

600 through 700

NOTE:

Insert the clevis pins from the outside in as shown in the inset images of Figure 20.

NOTE:

It is very important to maintain this order and direction while installing these hardware pieces. After installation, make sure that the grass bag cover pivots on the sup-

port tube and opens.

9

Image 9

Contents OPERATOR’S MANUAL READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATIONTo The Owner Carton Contents Assembly Parts Lists Warranty Twin Rear Bagger KitFinding and Recording Model Number TABLE OF CONTENTSCustomer Support BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENTDetermine The Model of Your Rider FastAttach Twin Bag Grass CollectorRider Model Identiﬁcation Sample Model NumberCONTENTS OF CARTON Carton Contentstoll free at One Chute TubeCONTENTS OF HARDWARE PACK # = QuantityRH = Right Hand LH = Left Hand Attaching The Bracket Assembly Attaching Bracket AssemblyModel Series 600 through Before assembly, place the tractor on a firmAttaching Bracket Assembly Attaching Support Bracket Bracket AssemblyAssembling Support Brackets Model Series 650 throughSelf tap Model Seriesscrews Inner HoleAttaching Grass Bags Grass Bag Cover Attaching Grass Bags & Grass Bag Cover600 through All Model SeriesAttaching Discharge Chute On Older Model RidersDischarge Chute All Model Series Bagger UsageAll Models - 600 through set the parking brakeFor parts and/or accessories please call Rear Twin BaggerPart List PART NUMBER Grass catcher Cover AssemblyHex Flange Lock Nut, 1/4-20 Discharge Chute 38”/42” BagMANUFACTURER’S LIMITED WARRANTY FOR Modelos OHD-190-180 Kit de embolsado posterior dobleMANUAL DEL OPERADOR IMPORTANTEAsistencia al cliente Búsqueda y registro del número de modeloÍNDICE ANTES DE COMENZAR A MONTAR SU NUEVO EQUIPOcación del modelo de podadora tractor IdentiﬁDetermine el modelo de la podadora tractor FastAttach con sistema de bolsa dobleContenido de la caja CONTENIDO DE LA CAJAUn tubo de canal Un conjunto de canal de descarga CONTENIDO DEL PAQUETE DE ELEMENTOS DE FERRETERÍA Instalación Conjunto de soporte Instalación Conjunto de soporteModelos series 600 a inclusive Modelos series 650 a 699 inclusiveInstalación del soporte y del conjunto del soporteInstalación del conjunto del soporte Ensamblado de los soportesEnsamblado de los soportes Instalación del soporte y del con- junto del so- porteModelo Serie Vea la FiguraTodos los modelos series 600 a inclusiveFigura Figura Figura de pasto gire sobre el tubo de soporte y se abra FiguraEn tractores de modelos más antiguos Instalación del canal de descargaTodos los modelos series 600 a 699 inclusive NOTA Figura AB Figura Canal de descarga FiguraTodas las series de modelos Uso de la embolsadoraTodos los modelos - 600 a inclusive Tira de retención Pasador de la tolva para recorte de césped FiguraEmbolsa dora doble posterior Lista de piezasPara piezas y/o accesorios por favor llame al accesorios por favor llame al 1-800-800- 7310-6483 ó al Para piezas y/oNo. DE NÚMERO DEEsta garantía limitada no lo cubrirá en los siguientes casos GARANTÍA LIMITADA DEL FABRICANTE PARAf. Piezas de reemplazo que no son piezas genuinas de MTD g. Gastos de transporte y llamadas por servicios técnicosModèles OHD-190-180 Collecteur arrière à deux sacsMANUEL DE L’OPÉRATEUR IMPRIMÉ AUXSupport client Pour trouver et enregistrer le numéro de modèleTABLE DES MATIERES AVANT D’ASSEMBLER VOTRE NOUVEL ÉQUIPEMENTdu modèle du tracteur IdentiﬁcationCollecteur d’herbe à deux sacs FastAttach Déterminer le modèle de votre tracteurCONTENU DU CARTON Contenu du cartonPIÈCES DE QUINCAILLERIE Montage du support de ﬁxation Montage du support de ﬁxationModèles de série 600 à Modèles de série 650 àpalier sup- port et du support de ﬁxation Montage duMontage des paliers supports Modèle de série 650 àModèle de la série Modèle de la sérieVoir la Figure Montage des Montage des sacs à herbe et du couvercledu couvercle sacs à herbe etla goulotte d’éjection Montage deMontage de la goulotte d’éjection Sur les anciens modèles de tracteursTous les modèles Utilisation du collecteurTous les modèles - Série 600 à Patte de fixation Goupille du collecteur d’herbeCollecteur à deux sacsListe des pièces DESCRIPTION NUMÉRO DEPIÈCE Palier support CollecteurUtilisez cette page pour noter les informa tions importantes Utilisez cette page tions importantespour noter les informa g. Les frais de transport et les appels de maintenance GARANTIE LIMITÉE DU FABRICANTCette garantie limitée ne s’applique pas dans les cas suivants f. Les pièces de rechange qui ne sont pas fabriquées par MTD