MAINTENANCE INSTRUCTIONS
Cleaning the Bath
To clean your bath, simply use a mild, nonabrasive liquid deter- gent solution. You can protect and restore the gloss to a dulled acrylic surface by applying an acrylic polish or automotive paste wax.
Never use abrasive household cleaners on any Jacuzzi Whirl- pool Bath© product.
Repairs to the Surface
Major scratches and gouges which penetrate the acrylic surface will require refinishing. Contact your Jacuzzi Whirlpool Bath© dealer for special instructions.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the whirlpool system, it is recommended that the whirlpool bath be purged at least twice a month. For best results, however, we recommend that you purge your whirlpool bath after each use using our exclusive
Systems Clean ™ is available through an authorized Jacuzzi Whirl- pool Bath© Distributor or by calling us direct at
Instructions for use: Immediately after bathing and exiting the whirlpool bath, leave the bath water in the tub and add hot water, if necessary, so the water is at least 1" above the highest jet. Turn on the unit without the aerator. Pour the contents of the Systems Clean Packet 1 (taking care not to get the material on yourself) into the bath near the intake for the circulation pump. Repeat same process with Systems Clean Packet 2. It is important to use Packet 1 before Packet 2 to avoid a strong odor. Run the bath for 5 to 10 minutes. Drain completely and rinse any residue.
If you have followed the standard purging instructions above and still have an excess accumulation of bath residue and desire an alterna- tive cleaning mechanism, we recommend SUPER SYSTEMS CLEAN PLUS manufactured by Stearns Packaging to rectify this condition. This may be obtained by contacting us at
purge your whirlpool system with Systems Clean as recommended.
(For additional information about water content, contact us for a copy
of the Jacuzzi Water Quality Primer.)
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.
If you want to use any kind of bath additive, use only a small amount of
The use of certain bath oils, bubble baths and bath additives may increase the level of accumulations of bath residue in the whirlpool system. If excess accumulations persist, you should discontinue use of these products.
Suction Cover/Strainer Maintenance
Clean the suction cover/strainer of hair and debris when neces- sary. To do this, remove the center screw and detach the square cover. Clean the cover by backflushing debris from the holes. Re- place the suction cover immediately after cleaning. When reinstall- ing, orient the cover/strainer with the small notch at the bottom. The gasket must be inserted into the groove of the cover/strainer before reinstalling onto the suction fitting.
CAUTION: Keep hair a minimum of 6 inches away from the suc- tion fitting at all times when the whirlpool system is operating. Hair longer than shoulder length should be secured close to the head, or a bathing cap should be worn. Do not operate the whirlpool system with the suction cover removed! It is a safety device and must always be in place on the suction fitting to minimize the potential hazard of hair and body entrapment.
SUCTION COVER/STRAINER ASSEMBLY
COVER STRAINER
SUCTION
FITTING
SCREW
NOTCHGASKET
Lamp
If your unit has chromotherapy lighting and the lights fail to func- tion contact your Jacuzzi Whirlpool Bath© dealer. There are no cus- tomer serviceable components on the chromotherapy lighting. You may also visit our web site at http://www.jacuzzi.com/ to find the near- est authorized service agent listing for your Jacuzzi Comfort Plus tub.
LED LIGHT ASSEMBLY
LOCKING NUT
ENGLISH
LIGHT BEZEL
SHELL
11
Jacuzzi Whirlpool Bath© BP43000 2/05