SPECIFICATIONS
Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty information packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to installation, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling. Jacuzzi Whirlpool Bath© is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure.
ENGLISH
RECTANGULAR BATHS
L | W |
| 2" |
(Heater) | (51 mm) H |
SIDE VIEW | (Motor) |
END VIEW |
PLUS BATHS WITHOUT INTEGRAL SKIRT
L |
| (25 mm) | W |
|
| 1" |
|
(Heater) |
|
| H |
SIDE VIEW | (Motor) |
| END VIEW |
PLUS BATHS WITH INTEGRAL SKIRT
A |
B |
DRAIN/OVERFLOW
SPECIFICATIONS (Rectangular)
|
|
| DRAIN/OVERFLOW | CUTOUT | TOTAL WEIGHT/ | OPERATING | PRODUCT | SKIRT & | HEATER | |
MODEL |
| DIMENSIONS |
| DIMENSIONS | FLOOR LOADING | GALLONAGE | WEIGHT | MOUNTING | ||
|
|
|
|
|
|
|
|
|
| |
AMIGA™ PLUS | 72" | (1829 mm) L* | 70" x 34" | 772 lb | 50 U.S. gal | 105 lb | Optional, | Factory Installed | ||
| 36" | ( 914 mm) W | 14" | (356 mm) B |
| (351 kg)/ | (186 liters) | (48 kg) | (S750000 HEATER KIT) | |
|
|
|
| 43 lb/ft2 |
|
|
|
| ||
|
|
|
| (210 kg/m2) |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
CETRA© 536 | 60" | (1524 mm) L* | NA | 742 lb | 48 U.S. gal | 92 lb | Integral | Factory Installed | ||
PLUS | 36" | ( 914 mm) W | 9" | ( 229 mm) B |
| (337 kg)/ | (181 liters) | (42 kg) |
| (S750000 HEATER KIT) |
WITH INTEGRAL |
|
|
| 50 lb/ft2 |
|
|
|
| ||
SKIRT |
|
|
| (244 kg/m2) |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
SIGNA© 5 PLUS | 60" | (1524 mm) L* | 58" x 40" | 708 lb | 42 U.S. gal | 108 lb | Optional, | Factory Installed | ||
| 42" | (1067 mm) W |
| (321 kg)/ | (159 liters) | (49 kg) | (S750000 HEATER KIT) | |||
|
|
|
| 40 lb/ft2 |
|
|
|
| ||
| 22" | ( 559 mm) H |
|
|
| (195 kg/m2) |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
SIGNA© 6 PLUS | 72" | (1829 mm) L* | 70" x 40" | 826 lb | 55 U.S. gal | 118 lb | Not | Factory Installed | ||
| 42" | (1067 mm) W | 14" | (356 mm) B |
| (375 kg)/ | (208 liters) | (54 kg) | Available | (S750000 HEATER KIT) |
|
|
|
| 39 lb/ft2 |
|
|
|
| ||
| 22" | ( 559 mm) H |
|
|
| (190 kg/m2) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*Add 1/4" to this dimension when
NOTE: The overall dimensions are nominal with a tolerance of +0 and
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
RapidHeatTM: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
1
Jacuzzi Whirlpool Bath© BP43000 2/05