Homelite UT10526 Mixing the Fuel, Oxygenated Fuels, Premium Exact MIX Gasoline, Lubricant

Page 12

operation

WARNING:

Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting the engine. DO NOT SMOKE! Stay away from open flames or sparks. Failure to heed this warning could result in serious personal injury.

FUEL AND REFUELING HANDLING THE FUEL SAFELY

WARNING:

Check for fuel leaks. If any are found, correct them before using the saw to prevent fire or burn injury.

nAlways handle fuel with care; it is highly flam- mable.

nAlways refuel outdoors and do not inhale fuel vapors.

nDo not let gasoline or lubricant come in contact with skin.

nKeep gasoline and lubricant away from the eyes.

If gasoline or lubricant comes in contact with the eyes, wash them immediately with clean water. If irritation is still present, see a doctor immediately.

nClean up spilled fuel immediately.

Refer to Refueling in the Specific Safety Rules section of this manual for additional safety infor- mation.

MIXING THE FUEL

nThis product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle lubri- cant. Pre-mix unleaded gasoline and 2-cycle engine lubricant in a clean container approved for gasoline.

nThis engine is certified to operate on unleaded gasoline intended for automotive use with an octane rating of 87 [(R + M) / 2] or higher.

■n Do not use any type of pre-mixed gasoline/lubri- cant from fuel service stations, this includes the pre-mixed gasoline/lubricant intended for use in mopeds, motorcycles, etc.

■nUse a high quality 2-cycle self-mixing lubricant for air-cooled engines. Do not use automotive lubricant or 2-cycle outboard lubricant.

■nMix 2% lubricant into the gasoline. This is a 50:1 ratio.

nMix the fuel thoroughly and each time before fueling.

■nMix in small quantities. Do not mix quantities larger than usable in a 30-day period. A 2-cycle lubricant containing a fuel stabilizer is recom- mended.

PREMIUM EXACT MIX™ (50:1)

GASOLINE

Lubricant

1 Gallon (US)

2.6 oz.

1 Liter

20 cc (20 ml)

OXYGENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR WARRANTY.

NOTE: Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates stated below are not covered under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume (commonly referred to as E10) or 15% ethanol by volume (commonly referred to as E15) are acceptable. E85 is not.

Page 12 — English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents UT10522, UT10526 / 20 in cc Chain Saw UT10519 / 18 in cc Chain SawToutes LES Versions Todas LAS Versiones Table of Contents IntroductionGeneral safety rules  Use safety footwear. Wear snug-fittingRead ALL Instructions Specific safety rules Do not adapt the powerhead to a bow guideRefueling do not Smoke KickbackTighten the fuel cap securely after refueling Symbols Symbol Signal Meaning ServiceGlossary of terms Features Product SpecificationsKnow Your Chain SAW Choke LeverGuide BAR LOW Kickback SAW ChainAssembly OperationUnpacking Packing ListDo not USE E85 FUEL. IT will Void Your Warranty Mixing the FuelOxygenated Fuels Premium Exact MIX GasolineFilling the fuel Tank Adding bar and chain lubricantSee Figure Operating the Chain Brake Starting the EngineSee Figures 4 See Figures 6To Start a Warm Engine Adjusting Idle Speed Stopping the EngineSee Figures 12 Pull and Push Kickback Precautions Preparing for Cutting Proper Grip on HandlesSee Figures 16 Work Area Precautions Proper Cutting StanceProper Procedure for Tree Felling Felling Trees Hazardous ConditionsSee Figures 21 Removing Buttress Roots Bucking Bucking with a WedgeBucking Logs Under Stress OverbuckingUnderbucking Limbing and Pruning Cutting SpringpolesSee Figures 31 Maintenance General MaintenanceLubrication Replacing the guide BAR and ChainCutters chain rotation Chain drive links Bar Groove Sprocket Adjusting the Chain Tension See Figures 44Chain Maintenance See Figures 47Sharpening the Cutters See Figures 49TOP Plate Filing Angle Side Plate AngleMaintaining Depth Gauge Clearance SeeMaintaining the Guide BAR Mounting the SAFE-T-TIPNOSE GuardMaintaining the SAFE-T-TIPNOSE Guard See Figures 59Cleaning the AIR Filter Choose one of the following cleaning optionsSee Figures 61 Cleaning the Starter Unit Adjusting the CarburetorBefore adjusting the carburetor Cleaning the Engine Checking the Fuel FilterReplacing the Spark Plug See Figures 67Inspecting and cleaning Chain Brake When storing 1 month or longerSpark Arrestor Storing the ProductTroubleshooting ProblemSolution Bar and chain combinationsProblem Possible Cause Solution Speed. Refer to Adjusting the CarburetorRefer to Replacing the Guide Bar and Chain Warranty Limited Warranty Statement40 English Warranty Emissions Maintenance Schedule and Warranted Parts ListEmissions Parts Inspect Clean Replace 800Règles de sécurité générales AVERTISSEMENT Lire Toutes LES Instructions Règles de sécurité particulières Ne pas adapter le bloc-moteur à un guideApprovisionnement EN Carburant NE PAS FUMER  RebondSymboles Symbole Signal Signification DépannageGlossaire Caractéristiques SpécificationsPour SE Familiariser Avec LA Scie À Chaîne Levier DE Volet DE DépartProtection DE Poignée Avant / Frein DE Chaîne GuideDéballage Liste DE Contrôle D’EXPÉDITIONListe DE Contrôle D’EXPÉDITION continu Mélange DU Carburant Carburants OxygénésMélange Premium Exact LubrifiantRemplissage DU Réservoir DE Carburant Appoint De lubrifiant Pour Guide ET ChaîneVoir la figure Utilisation DU Frein DE Chaîne Démarrage DU MoteurVoir les figures 4 et Voir les figures 6 àDémarrage du moteur chaud  Arrêt DU Moteur Réglage DuralentiVoir les figures 12 et Poussée ET Traction Précautions À Prendre Pour Éviter LE Rebond Voir les figures 16 etPosition DE Coupe Correcte Précautions À Prendre SUR LE Lieu DE TravailMéthodes D’UTILISATION / Coupe Élémentaires Abattage D’ARBRES Situations Dangereuses AVERTISSEMENT  Méthode Correcte D’ABATTAGE Voir les figures 21 àÉlimination DES Racines Échasses DébitageTronçonnage Avec Coins Débitage DE Billes Sous Contrainte Coupe PAR LE DessusCoupe PAR LE Dessous Ébranchage ET Émondage Coupe DE FouetsVoir les figures 31 et Remplacement DU Guide ET DE LA Chaîne Entretien GénéralLubrification Voir les figures 34 àMaillons D’ENTRAÎNEMENT Pignon Rainure DU Guide Réglage DE LA Tension DE Chaîne Voir les figures 44 àEntretien DE LA Chaîne Voir les figures 47 etAffûtage DES Dents Voir les figures 49 àVoir Réglage de la tension de chaîne Angle D’AFFÛTAGE DE LA Plaque Supérieure Angle DE Plaque LatéraleMaintien DU JEU DU Limiteur DE Profondeur Voir les figures 55 àInstallation DE LA Garde SAFE-T-TIP Entretien DU GuideEntretien DE LA Garde SAFE-T-TIP Voir les figures 59 etNettoyage DU Filtre À AIR Voir les figures 61 àNettoyage DU Lanceur Réglage DU CarburateurAvertissement Voir le etRemplacement DE LA Bougie Nettoyage DU MoteurAvertissement Vérification DU Filtre À CarburantPARE-ÉTINCELLES Inspection ET Nettoyage DU Frein DE ChaîneRemisage LE Produit Voir les figures 71 etProblème Cause possible Solution De référenceDu guide De la chaîne ’entraînement 50 cm 20 pulg 310629001 45 cm 18 pulgRéglage de la tension de chaîne de la section Entretien de Garantie Déclaration DE Garantie Limitée40 Français Nous Appeler D’ABORD Reglas de seguridad generales AdvertenciaReglas de seguridad específicas Apague el motor antes de poner en reposo laReabastecimiento DE Combustible ¡NO Fume ContragolpeSímbolos Símbolo Nombre Denominación / ExplicaciónSímbolo Señal Significado Peligro ServicioCausará la muerte o lesiones serias Glosario de términos Corte trasero de talaCaracterísticas Especificaciones DEL ProductoFamiliarícese CON LA Motosierra Palanca DEL AnegadorCadena DE Sierra DE Contragolpe Moderado Gatillo DEL AceleradorArmado FuncionamientoDesempaquetado Lista DE EmpaquetadoMezclado DEL Combustible Combustibles OxigenadosPremium Exact MIX Gasolina LubricanteLlenado DEL Tanque Abastecimiento de lubricante para la barra y la cadenaVea la figura Funcionamiento DEL Freno DE LA Cadena Arranque DEL MotorVea las figuras 4 y Vea las figuras 6 aPrecaución Apagado DEL Motor Ajuste DE LA Marcha LentaVea las figuras 12 y Empujón Y Tirón Precauciones Relacionadas CON EL Contragolpe Preparación Para EL Corte Sujeción Correcta DE LOS MangosVea las figuras 16 y Postura Correcta Para EL Corte Precauciones Relacionadas CON EL Área DE TrabajoProcedimientos Básicos DE Funcionamiento Y Corte Tala DE Árboles Condiciones Peligrosas AdvertenciaProcedimiento Correcto Para Talar Árboles Vea las figuras 21 aEliminación DE Raíces Zancas TronzadoTronzado CON Cuña Tronzado DE Troncos Bajo TensiónTronzado POR Arriba Tronzado POR AbajoCorte DE Pértigas Mantenimiento Mantenimiento GeneralLubricación Cómo reemplazar la barra guía y la cadenaPasador De ajuste Orificio del Página 27 Español Ajuste DE LA Tensión DE LA Cadena Mantenimiento DE LA CadenaVea las figuras 44 a Vea las figuras 47 yAfilado DE LOS Dientes DE Corte Vea las figuras 49 aÁngulo DE Limadura DE LA Placa Superior Ángulo DE LA Placa LateralMantenimiento DEL Espacio Libre DEL Calibre DE Profundidad Mantenimiento DE LA Barra GuíaVea las figuras 55 a Montaje DE LA Protección SAFE- T-TIPDE LA Punta Mantenimiento DE LA Protección SAFE-T-TIPDE LA PuntaVea las figuras 59 y Limpieza DEL Filtro DE Aire Vea las figuras 61 aEscoja una de los siguientes métodos optativos de limpieza Limpieza DE LA Unidad DEL Arrancador Ajuste DEL CarburadorVea la figura 65 y Antes de ajustar el carburadorLimpieza DEL Motor Revisión DEL Filtro DE CombustibleCambio DE LA Bujía Vea las figuras 67 aParachispas Inspección y limpieza del freno de la cadenaAlmacenamiento DE LA Producto Vea las figuras 71 ySolución de problemas Problema Causa posible SoluciónCombinaciones de barra y cadena 900920027 45 cm 18 pulgFuncionamiento del freno de la cadena en la sección Garantía Declaración DE LA Garantía LimitadaPágina 40 Español Llámenos Primero UT10522, UT10526 / 20 in cc Chain Saw Manuel D’UTILISATION Manual DEL OperadorUT10519 / 18 in cc Chain Saw Homelite Consumer PRODUCTS, INC

UT10522, UT10519, UT10526 specifications

The Homelite UT10526, UT10519, and UT10522 are powerful trimmers that cater to the needs of homeowners and landscaping professionals alike. These models are part of Homelite’s expanding line of tools designed for efficient yard maintenance, each boasting its unique features and technological innovations.

The Homelite UT10526 is particularly notable for its 26cc, 2-cycle engine, which provides a blend of power and lightweight handling. This trimmer is designed to deliver robust performance, making it suitable for tackling tough weeds and dense grass. It features an easy-start system that significantly reduces the amount of pull force needed to start the engine, enhancing user convenience. Additionally, the UT10526 is equipped with a dual-line bump feed head, allowing for quick and easy line advances, which ensures uninterrupted operation during trimming tasks.

Moving on to the UT10519, this model stands out with its ergonomic design. Weighing slightly less than its counterpart, it features a 19-inch cutting width that makes it ideal for precision trimming around garden beds and fences. The UT10519 utilizes a curved shaft design, providing better control and maneuverability, especially in tight spaces. Its 25cc engine is efficient in fuel consumption while maintaining exceptional power for various cutting tasks. The adjustable handle ensures that users can find the most comfortable grip, reducing strain during extended use.

Lastly, the Homelite UT10522 boasts advanced technological features, including a powerful 22cc engine that offers smooth operation and low vibration. This model is designed with a straight shaft, making it perfect for reaching under shrubs and other obstacles. The UT10522 also incorporates an automatic line advancement system, eliminating the need for manual adjustments while relieving the hassle of line replacement. Furthermore, the lightweight construction makes it easy to maneuver, especially for longer landscaping jobs.

In summary, the Homelite UT10526, UT10519, and UT10522 are engineered with practicality and efficiency in mind. They blend power, lightweight design, and user-friendly features, making them ideal companions for yard maintenance. These trimmers cater to various needs, ensuring that both casual users and professional landscapers can effectively manage their outdoor spaces with ease and comfort.
Top Page Image Contents