Alliance Laundry Systems CHM1772C Steam Requirements Steam Heat Option Only, Supply Dispensing

Page 54

Installation

Steam Requirements (Steam Heat Option Only)

WARNING

Hot Surfaces. Will cause severe burns. Turn steam off and allow steam pipes, connections and components to cool before touching.

W505

For machines equipped with optional steam heat, install piping in accordance with approved commercial steam practices. Steam requirements are shown in Table 16.

Steam Supply Information

Steam inlet

 

40 – 80 pound

1/2 in. (13 mm)

connection size

 

 

 

 

125 pound

3/4 in. (19 mm)

 

 

 

 

 

 

Number of steam inlets

 

1

 

 

 

Recommended pressure

 

30 – 80 psi

 

 

 

(2.0 – 5.4 bar)

 

 

 

Maximum pressure

 

80 psi

 

 

 

(5.4 bar)

 

 

 

 

 

 

Table 16

 

IMPORTANT: Failure to install the customer supplied steam filter may void the warranty.

Supply Dispensing

WARNING

Dangerous Chemicals. May damage eyes and skin. Wear eye and hand protection when handling chemicals; always avoid direct contact with raw chemicals. Read the manufacturer’s directions for accidental contact before handling chemicals. Ensure an eye-rinse facility and an emergency shower are within easy reach. Check at regular intervals for chemical leaks.

 

 

W363

 

 

 

 

 

Supply Dispensing

 

 

 

 

Capacities

20 – 80

125

 

 

 

Number of supply

4

0 or 5

compartments

 

(optional)

 

 

 

Number of external

 

 

liquid supply

5

5

connections (OPL only)

 

 

Liquid supply

3/8 in.

5/8 in.

connection size

(8 mm)

(15.9 mm)

 

 

 

Table 17

IMPORTANT: Undiluted chemical dripping can damage the machine. All chemical injection supply dispenser pumps and dispenser tubing should be mounted below the washer’s injection point. Loops do not prevent drips if these instructions are not followed.

IMPORTANT: Failure to follow these instructions could damage the machine and void the warranty.

52

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F8208301

Image 54
Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Do not bypass any safety devices in the machineModel Identification ModelIntroduction Pound 125Delivery Inspection Nameplate LocationCN040GC2OUID01 Introduction Model Number Familiarization GuideReplacement Parts Customer ServiceSpeed Models Specification Weight and Shipping Information Wash Cylinder InformationDrive Train Information Power ConsumptionEstimated Building Heat Load Cylinder SpeedsElectrical Heating Optional Number of motors in drive train Drive motor power, hp kW Electrical Heating Specifications and Dimensions Specifications and Dimensions Machine Capacity Dimensions 92 in 252 mm 94 in 202 mm Dimensional Clearances Machine Capacity Dimensional Clearances Dimensions 125Machine Foundation Minimum Depth Methods RequirementMinimum Floor Load Data, 2 Speed Models Specification Floor Load Data, Variable-Speed Models Specification 125Concrete Foundation Installation 20, 30, 40 and 60 ModelsInstallation Models Machine Anchoring Direct-to-Finished-Floor InstallationAnchor Specifications Refer to Figure Ft.- lbsElevated Base Frame Installation Completed expansion bolt installation is shown in FigureP035I Mounting Bolt Hole Locations Without Elevated Base Frames ModelsFront of Frame 19 mm 45 mm 660 mm 32 mm 41.5 1054 mm 1219 mm Mounting Bolt Hole Locations With Elevated Base Frames CHM2072N 92 mm 56 mm Drain Connection Drain TroughDrain Information 125 Drain Line Sizing Minimum Drain ID Model Number of MachinesNumber Supply Line Size Machines Water Connection RequirementsCabinet Hardmount Water Supply Information Hot/ColdElectrical Installation Requirements Input Power Conditioning Input Power Condition Corrective ActionCircuit Breakers and Quick Disconnects Connection SpecificationsInput Voltage Requirements GroundingPhase Adder Thermal Overload ProtectorInstallation Electrical Specifications Pound Capacity Models Standard Electric Heat380 440 200 208 Variable-Speed Models 380-415 440-480 200 208-240 10.0 380 50/60 10.0 Steam Supply Information Steam Requirements Steam Heat Option OnlySupply Dispensing Supply DispensingExternal Supplies Connection of External Liquid Supplies 20 80 Pound OPL ModelsStart Up Basket Rotation
Related manuals
Manual 19 pages 8.07 Kb