Alliance Laundry Systems CHM1772C manual P035I

Page 31

3.Refer to Figure 9 and Table 4 to set the drill depth gauge.

4.Drill the holes to the set depth. Refer to Table 4.

5.Use compressed air or a squeeze bulb to remove debris from each hole.

6.Fill half the hole depth with an industry accepted adhesive anchoring system.

7.Insert bolt until it reaches the bottom of the hole and 1.5 inches (38 mm) of the bolt extends above the base frame. Refer to Figure 10.

8.Allow adhesive around the bolt to cure properly.

9.Position base frame over anchoring bolts.

10.Raise and level the base frame .5 inch (13 mm) off the floor on three points, using spacers such as nut fasteners.

11.Fill the space between the base frame and the floor with a good quality non-shrinking machinery grout to ensure a stable installation. Grout completely under all frame members.

12.Position washers and locknuts on bolts and finger tighten nuts to base frame.

13.Before grout sets completely, make a drain opening in the grouting at the rear of the base frame with a stiff piece of wire. This opening should be approximately .5 inch (13 mm) wide to allow any surface water build-up under the base of the machine to drain away. This drain opening must not be near frame mounting bolts. Do not omit this step.

14.Allow machine grout to set, but not cure.

15.Remove the spacers carefully, allowing the base frame to settle into the wet grout.

16.Tighten nuts by even increments – one after the other using the specified torque – until all are tightened evenly and the base frame is fastened securely to the floor. Refer to Table 4.

Installation

17.Position the machine over the base frame, aligning the mounting holes on the machine with the corresponding holes on the frame.

18.Install a bolt, lockwasher, and nut in each mounting hole. Use 5/8 inch – 18 x 2.00 grade 5 mounting bolts with 5/8 inch – 18 grade B nuts and 5/8 inch lockwashers.

19.Hand tighten each nut.

20.Tighten the two rear nuts two turns.

21.Tighten the two front nuts two turns.

22.On 30, 40 and 60 models, tighten the two middle nuts firmly.

23.Tighten the two front nuts firmly; tighten the two rear nuts firmly.

NOTE: Check and retighten the locknuts after five to ten days of operation and every three months thereafter.

NOTE: For 80 and 125 pound models, a bolt-locator fixture or rebar frame is available as an option. This is designed to be embedded in concrete. Refer to Figure 12.

IMPORTANT: Do not install any 80 or 125 machines on an elevated base frame.

1

2

3

4

P035I

1Machine Base

2Mounting Bolt Threads

3Grouting

4Bolt-Locator Fixture or Rebar Frame

Figure 12

F8208301

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

29

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Washer-Extractors Page Contents Important Safety Instructions Explanation of Safety MessagesSafety Information Safety Decals Do not bypass any safety devices in the machine Operator SafetyModel Model IdentificationIntroduction 125 PoundNameplate Location Delivery InspectionIntroduction Model Number Familiarization Guide CN040GC2OUID01Customer Service Replacement PartsWash Cylinder Information Speed Models Specification Weight and Shipping InformationCylinder Speeds Power ConsumptionEstimated Building Heat Load Drive Train InformationElectrical Heating Optional Number of motors in drive train Drive motor power, hp kW Electrical Heating Specifications and Dimensions Specifications and Dimensions Machine Capacity Dimensions 92 in 252 mm 94 in 202 mm Machine Capacity Dimensional Clearances Dimensions 125 Dimensional ClearancesMinimum Depth Methods Requirement Machine FoundationMinimum Floor Load Data, Variable-Speed Models Specification 125 Floor Load Data, 2 Speed Models Specification20, 30, 40 and 60 Models Concrete Foundation InstallationInstallation Models Ft.- lbs Direct-to-Finished-Floor InstallationAnchor Specifications Refer to Figure Machine AnchoringCompleted expansion bolt installation is shown in Figure Elevated Base Frame InstallationP035I Models Mounting Bolt Hole Locations Without Elevated Base FramesFront of Frame 19 mm 45 mm 660 mm 32 mm 41.5 1054 mm 1219 mm Mounting Bolt Hole Locations With Elevated Base Frames CHM2072N 92 mm 56 mm Drain Trough Drain ConnectionDrain Line Sizing Minimum Drain ID Model Number of Machines Drain Information 125Hot/Cold Water Connection RequirementsCabinet Hardmount Water Supply Information Number Supply Line Size MachinesElectrical Installation Requirements Input Power Condition Corrective Action Input Power ConditioningGrounding Connection SpecificationsInput Voltage Requirements Circuit Breakers and Quick DisconnectsThermal Overload Protector Phase AdderStandard Electric Heat Installation Electrical Specifications Pound Capacity Models380 440 200 208 Variable-Speed Models 380-415 440-480 200 208-240 10.0 380 50/60 10.0 Supply Dispensing Steam Requirements Steam Heat Option OnlySupply Dispensing Steam Supply InformationExternal Supplies 20 80 Pound OPL Models Connection of External Liquid SuppliesBasket Rotation Start Up
Related manuals
Manual 19 pages 8.07 Kb
Top Page Image Contents