Alliance Laundry Systems CHM1772C Concrete Foundation Installation, 20, 30, 40 and 60 Models

Page 26

Installation

Concrete Foundation Installation

A concrete foundation pad may be constructed to elevate the machines. The concrete foundation pad must be poured, reinforced with rebar and tied to the existing floor with reinforcing bars. Refer to Figure 6, Figure 7 or Figure 8 for a typical concrete foundation pad installation.

1.Verify that the floor meets the requirements given in the Machine Foundation section.

2.Excavate the floor to a depth of approximately 9 inches (230 mm) below the floor surface, making certain that the sides of the hole slope outwards from top to bottom. The bottom of the hole should be 6 inches (152 mm) larger all around than the top.

 

WARNING

3. Wet the hole well and brush the bottom and sides

 

 

with cement grout.

To reduce the risk of fire, this appliance must be bolted to an uncovered concrete floor.

 

W731

 

 

 

 

B

 

 

 

 

C

 

A

 

 

 

 

 

D

 

E

 

 

 

 

 

CHM2281N

 

20, 30, 40 AND 60 MODELS

 

 

 

 

CHM2281N

A

Pad height must not exceed 8 in. (203 mm)

D

4 in. (102 mm) minimum

B

above existing floor

 

(2 and F-Speed Models)

.5 in. (13 mm) minimum

 

6 in. (152 mm) minimum (V-Speed Models)

C

4 in. (102 mm) minimum

E

Concrete reinforcing bar

Figure 6

24

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F8208301

Image 26
Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Do not bypass any safety devices in the machineModel Identification ModelIntroduction Pound 125Delivery Inspection Nameplate LocationCN040GC2OUID01 Introduction Model Number Familiarization GuideReplacement Parts Customer ServiceSpeed Models Specification Weight and Shipping Information Wash Cylinder InformationDrive Train Information Power ConsumptionEstimated Building Heat Load Cylinder SpeedsElectrical Heating Optional Number of motors in drive train Drive motor power, hp kW Electrical Heating Specifications and Dimensions Specifications and Dimensions Machine Capacity Dimensions 92 in 252 mm 94 in 202 mm Dimensional Clearances Machine Capacity Dimensional Clearances Dimensions 125Minimum Machine FoundationMinimum Depth Methods Requirement Floor Load Data, 2 Speed Models Specification Floor Load Data, Variable-Speed Models Specification 125Concrete Foundation Installation 20, 30, 40 and 60 ModelsInstallation Models Machine Anchoring Direct-to-Finished-Floor InstallationAnchor Specifications Refer to Figure Ft.- lbsElevated Base Frame Installation Completed expansion bolt installation is shown in FigureP035I Mounting Bolt Hole Locations Without Elevated Base Frames ModelsFront of Frame 19 mm 45 mm 660 mm 32 mm 41.5 1054 mm 1219 mm Mounting Bolt Hole Locations With Elevated Base Frames CHM2072N 92 mm 56 mm Drain Connection Drain TroughDrain Information 125 Drain Line Sizing Minimum Drain ID Model Number of MachinesNumber Supply Line Size Machines Water Connection RequirementsCabinet Hardmount Water Supply Information Hot/ColdElectrical Installation Requirements Input Power Conditioning Input Power Condition Corrective ActionCircuit Breakers and Quick Disconnects Connection SpecificationsInput Voltage Requirements GroundingPhase Adder Thermal Overload ProtectorInstallation Electrical Specifications Pound Capacity Models Standard Electric Heat380 440 200 208 Variable-Speed Models 380-415 440-480 200 208-240 10.0 380 50/60 10.0 Steam Supply Information Steam Requirements Steam Heat Option OnlySupply Dispensing Supply DispensingExternal Supplies Connection of External Liquid Supplies 20 80 Pound OPL ModelsStart Up Basket Rotation
Related manuals
Manual 19 pages 8.07 Kb