Dolmar MS-331 C Emissions Component Defect Warranty Coverage, Parts Covered, What is not Covered

Page 3

6. Consequential Coverage

Coverage hereunder shall extend to the failure of any engine compo- nents caused by the failure of any warranted part still under warranty.

EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE

DOLMAR GmbH North American Division (Dolmar) warrant to the ini- tial retail purchaser and each subsequent owner, that this utility equipment was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U.S.

Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this engine to fail to conform with EPA regulations during its warranty period.

For the components listed under PARTS COVERED, the service dealer authorized by Dolmar will, at no cost to you, make the neces- sary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U.S. EPA regulations.

EMISSISON COMPONENT DEFECT WARRANTY PERIOD

The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years.

PARTS COVERED

Listed below are the parts covered by the Emission Components Defect Warranty. Some of the parts listed below may require sched- uled maintenance and are warranted up to the first scheduled replacement point for that part.

(1)Fuel Metering System

(i)Carburetor and internal parts

(ii)Fuel filter, if applicable.

(iii)Throttle stopper, if applicable.

(iv)Choke System, if applicable.

(2)Air Induction System

(i)Air cleaner plate

(ii)Air cleaner case

(3)Ignition System

(i)Spark plugs.

(ii)Flywheel Magneto

(iii)Ignition Coil.

(4)Miscellaneous Items Used in Above Systems

(i)Fuel hoses, clamps and sealing gaskets

OBTAINING WARRANTY SERVICE

To obtain warranty service, take your engine to the nearest DOLMAR Factory Service Center or service Center authorized by Dolmar. Bring your sales receipts indicating date of purchase for this engine. The dealer of service authorized by Dolmar will perform the necessary repairs or adjustments within a reasonable amount of time and fur- nish you with a copy of the repair order. All parts and accessories replaced under this warranty become the property of Dolmar.

WHAT IS NOT COVERED

Conditions resulting from tampering, misuse, improper adjustment (unless they were made by the service dealer authorized by Dolmar during a warranty repair), alteration, accident, failure to use the rec- ommended fuel and oil, or not performing required maintenance services.

-The replacement parts used for required maintenance services.

-Consequential damages such as loss of time, inconvenience, loss of use of the engine or equipment, etc.

-Diagnosis and inspection charges that do not result in war- ranty-eligible service being performed.

-Any non-authorized replacement part, or malfunction of autho- rized parts due to use of non-authorized parts.

OWNER’S WARRANTY RESPONSIBILITIES

As the engine owner, you are responsible for the performance of the required maintenance listed in your owner's manual. Dolmar recom- mends that you retain all receipts covering maintenance on your engine, but Dolmar cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all sched- uled maintenance. As the engine owner, you should however be aware that Dolmar may deny warranty coverage if your engine or a part has failed due to abuse, neglect, improper maintenance or unap- proved modifications.

You are responsible for presenting your engine to the nearest service dealer authorized by Dolmar when a problem exists.

If you have any questions regarding your warranty rights and respon- sibilities, you should contact the Dolmar Warranty Service Depart- ment at 1-888-OPE-PART for the information.

THINGS YOU SHOULD KNOW ABOUT THE EMISSION CONTROL SYSTEM WARRANTY:

MAINTENANCE AND REPAIRS

You are responsible for the proper maintenance of the engine. You should keep all receipts and maintenance records covering the per- formance of regular maintenance in the event questions arise.

These receipts and maintenance records should be transferred to each subsequent owner of the engine. Dolmar reserves the right to deny warranty coverage if the engine has not been properly main- tained. Warranty claims will not be denied, however, solely because of the lack of required maintenance or failure to keep maintenance records.

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CON- TROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A SERVICE DEALER AUTHO- RIZED BY Dolmar. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM.

If other than the parts authorized by Dolmar are used for mainte- nance replacements or for the repair of components affecting emis- sion control, you should assure yourself that such parts are warranted by their manufacturer to be equivalent to the parts autho- rized by Dolmar in their performance and durability.

HOW TO MAKE A CLAIM

All repair qualifying under this limited warranty must be performed by a service dealer authorized by Dolmar. In the event that any emis- sion-related part is found to be defective during the warranty period, you shall notify Dolmar Warranty Service Department at 1-888-OPE- PART. Dolmar and you will be advised of the appropriate warranty service dealer or service providers where the warranty repair can be performed.

3

Image 3
Contents Importante Recommandation importanteEnglish Table of contentsDolmar GmbH North American Division Warranty Coverage Owner’s Warranty ResponsibilitiesWhat is not Covered Emissions Component Defect Warranty CoverageEmissison Component Defect Warranty Period Obtaining Warranty ServiceSymbols ON/STARTOFF/STOP Personal protective equipment Safety InstructionsGeneral Instructions Intended use of the machineKickback prevention RefuelingMethod of operation KickbackTechnical Data Maintenance instructionsFirst Aid For machines with Loop Handle Mounting of HandleMounting of Protector For machines with U Handle modelsFor # MS-260 U/261 U and # MS-330 U/331 U Installing Cutter-BladeInstalling Nylon cutting head Mounting of Cutter Blade or Nylon Cutter HeadCorrect Handling of Machine FUELS/REFUELINGRE-SHARPENING the Cutting Tool Points in Operation and HOW to StopIdle Speed Adjustment StoppingServicing Instructions Nylon Cutting HeadSuction head in the fuel tank Cleaning of muffler exhaust portStorage Supply of grease to gear caseTroubleshooting Chart Maintenance ScheduleDolmar FrançaisCalifornie Seulement Responsabilités envers la garantie du propriétaireCE QUE LA Garantie NE Couvre PAS Période DE Garantie Contre LES Vices DES Pièces À ÉmissionPièces Couvertes PAR LA Garantie Demande Dapplication DE LA GarantieSymboles MARCHE/DÉMARRAGEArrêt Dispositifs de protection personnelle Consignes DE SécuritéConsignes générales Utilisation prévue pour loutilPrévention des chocs en retour RemplissageUtilisation Choc en retourModèle Données TechniquesInstructions dentretien Premiers secoursÉcran Surmoulée Oui noir Pour les modèles à poignée en boucle Assemblage DE LA PoignéeAssemblage DU Protecteur Pour les modèles à poignée en UInstallation de la lame du sécateur Installation de la tête de coupe en nylonPour les modèles MS-260 U/261 U et MS-330 U/331 U Comment Tenir Loutil CARBURANTS/REMPLISSAGEArrêt Réglage DE LA Vitesse DE Rotation À VideRaffûtage DE Loutil Tranchant Instructions Pour LA Réparation Tête DE Coupe EN NylonNettoyage de lorifice de sortie du silencieux RangementGraissage du carter dengrenage Crépine daspiration du réservoir de carburantTableau DE Dépannage Horaire DentretienÍndice EspañolCalifornia Solamente Responsabilidades del propietario para la garantíaResponsabilidades DEL Propietario DE LA Garantía Partes Cubiertas POR LA GarantíaObtención DEL Servicio DE Garantía QUÉ no Cubre LA GarantíaENCENDIDO/INICIO SímbolosEquipo de protección personal Instrucciones DE SeguridadInstrucciones generales Uso previsto para la máquinaPrevención contra los retrocesos bruscos RepostajeMétodo de operación Retroceso bruscoDatos Técnicos Instrucciones de mantenimientoPrimeros auxilios Pulgadas Conjunto del asidero Tipo Redondo En U Para máquinas con asidero redondo Montaje DEL AsideroMontaje DEL Protector Para máquinas del modelo con asideros en UInstalación del disco de corte Montaje DEL Disco DE Corte O Cabezal DEL Cordón DE NylonPara # MS-260 U/261 U y # MS-330 U/331 U Para # MS-230 C/231 C, MS-260 C/261 C y MS-330 C/331 CManejo Correcto DE LA Máquina COMBUSTIBLE/REPOSTAJEAfilado DEL Implemento DE Corte Puntos a Tener EN Cuenta EN LA Operación Y Cómo PararParada Ajuste DE LA Velocidad AL RalentíInstrucciones DE Mantenimiento Cabezal DEL Cordón DE NylonLimpieza del orificio de escape del silenciador AlmacenamientoSuministro de grasa a la caja de engranajes La cabeza de succión del depósito de combustiblePrograma DE Mantenimiento Gráfico DE Solución DE ProblemasPage Dolmar GmbH Postfach 70 04 Hamburg Germany