Husqvarna ProFlex 18 manual Transport, Never run the machine in an enclosed area

Page 12

SAFETY INSTRUCTIONS

Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon monoxide, an odourless, poisonous and highly dangerous gas.

Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting.

Never make adjustments with the engine running.

The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer.

The blades are sharp and can cause cuts. Wrap the blades or wear protective gloves when handling them.

Check regularly that the parking brake works. Adjust and maintain as required.

8010-060

Never run the machine in an enclosed area.

The mulching unit should only be used where

 

better quality mowing is required and in known

 

areas.

 

Reduce the risk of fire by removing grass, leaves

 

and other debris that may have fastened on the

 

machine. Allow the machine to cool before

 

putting it in storage.

 

Transport

 

The machine is heavy and can cause serious

 

crush injuries. Be especially careful when it is

 

loaded in or out of a car or on and off of a trailer.

 

Use an approved trailer to transport the ma-

8010-061

chine. Activate the parking brake, shutoff the fuel

Regularly clean grass, leaves and other debris from

supply and secure the machine using approved

the machine.

fasteners, such as tension belts, chains or ropes

 

when transporting.

 

Check and observe local road traffic regulations before transporting or driving the machine on roads.

IMPORTANT INFORMATION

The parking brake is not sufficient to lock the machine during transport. Ensure you secure the machine firmly to the transpor- ting vehicle. Reverse the machine on to the transporting vehicle to prevent it from overturning.

10 – English

Image 12
Contents Rider ProFlex EnglishSvenska Contents Instruction Dear customerTravel and transport on public roads TowingSafety Instructions Good serviceSerial number Explanation of Symbols Read the instructionsSafety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Never run the machine in an enclosed areaPresentation PresentationLocation of the controls Throttle control Choke leverSpeed limiter Speed of the machine is steplessly regulatedCutting unit Lift lever for cutting unitLever for adjustment of the cutting height Parking brakeSeat FuellingDriving Before startingStarting the engine Driving the machine 6007-210 Cutting tips MAXStopping the engine Disengage leverMaintenance Maintenance scheduleYear Hours Before after Year 100 300Dismantling of the machine hoods Engine hoodNose Right-hand fenderCheck the engine’s cooling air intake Check the transmission’s air intakeLeft-hand fender Transmission coverChecking and adjustment of the steering wires Checking and adjustment of the throttle wire Checking and adjusting the choke wireAdjusting the hydrostatic wire Adjusting the brakes Poorly adjusted brakes can result in reduced braking powerChecking the tyre pressure Replacing the air filter Replacement of the fuel filter Cleaning the pulse air filterChecking of the fuel pump’s air filter Check the level of the battery acid Procedures on contact with acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Fitting the cutting unit Take care. Risk of crushing injuryBelt diagram Watch your fingers. Do not turn the blades or beltCheck that the belt is fitted around the tension roller Parallelism Cutting heightReplacing the break-pin BioClip Service position for the cutting unit Placing in the service positionReleasing from the service position Checking the bladesDismantling the cutting unit 8009-169 Removing the attachment frame Dismantling the beltAssembling the belt Belt replacement on BioClip Replacing the cutting unit’s beltsBelt replacement on BioClip112 Removal of BioClip plug Combi Cutting unit modelsLubrication chart LubricationLubricating wires GeneralPedal mechanism in frame tunnel Chains in frame tunnel Engine oilGear lever TransmissionThrottle and choke wires, lever bearings Triangular linkDriver’s seat Oil filter, replacement Parking brake wireBelt tensioner Transmission oil levelTrouble Shooting Schedule Problem ProcedureService StorageWinter storage Wiring Diagram Technical Data Rider ProFlexRear ejector Combi Rear ejector BioClipEU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeServicejournal Pre-delivery serviceAfter first 8 hours Work doneHour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00