Husqvarna ProFlex 18 manual Fitting the cutting unit, Take care. Risk of crushing injury

Page 34

MAINTENANCE

The parts of the cutting unit

A cutting unit with a rear ejector has been used in the instructions below, however, the same procedure applies to other units if not otherwise stated.

The parts mentioned are:

A.

Catch

E. Height setting arm

B.

Inner pin

F. Parallel strut

C.

Hook guard

G. Lowest height setting stop

D.

Handle

 

Fitting the cutting unit

WARNING!

Take care. Risk of crushing injury.

Starting point for fitting the unit:

Place the Rider on a level surface.

Apply the brakes by pressing down the pedal and lock using the pushbutton.

The attachment frame in the lowered position.

The attachment frame locked with the hook guard and the catch (A) in the loaded position.

Attachment frame mounted on cutting unit, see ”Removing the attachment frame”

1.Fit the unit in the attachment frame’s outer hooks.

2.Pull out the catch (A) and release the hook guard by sliding its handle (D) backwards.

3.Lift the attachment by pulling up the lever located on the driver’s right-hand side.

D E

C

B

A F G

8009-188

A

8009-022

8009-024

D

A

8009-167

32 – English

Image 34
Contents Rider ProFlex EnglishSvenska Contents Travel and transport on public roads InstructionDear customer TowingGood service Safety InstructionsSerial number Explanation of Symbols Read the instructionsSafety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Never run the machine in an enclosed areaPresentation PresentationLocation of the controls Speed limiter Throttle controlChoke lever Speed of the machine is steplessly regulatedCutting unit Lift lever for cutting unitSeat Lever for adjustment of the cutting heightParking brake FuellingBefore starting DrivingStarting the engine Driving the machine 6007-210 Cutting tips MAXStopping the engine Disengage leverMaintenance schedule MaintenanceYear Hours Before after Year 100 300Nose Dismantling of the machine hoodsEngine hood Right-hand fenderLeft-hand fender Check the engine’s cooling air intakeCheck the transmission’s air intake Transmission coverChecking and adjustment of the steering wires Checking and adjustment of the throttle wire Checking and adjusting the choke wireAdjusting the hydrostatic wire Poorly adjusted brakes can result in reduced braking power Adjusting the brakesChecking the tyre pressure Replacing the air filter Cleaning the pulse air filter Replacement of the fuel filterChecking of the fuel pump’s air filter Procedures on contact with acid Check the level of the battery acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Fitting the cutting unit Take care. Risk of crushing injuryWatch your fingers. Do not turn the blades or belt Belt diagramCheck that the belt is fitted around the tension roller Parallelism Cutting heightReplacing the break-pin BioClip Releasing from the service position Service position for the cutting unitPlacing in the service position Checking the bladesDismantling the cutting unit 8009-169 Removing the attachment frame Dismantling the beltAssembling the belt Belt replacement on BioClip Replacing the cutting unit’s beltsBelt replacement on BioClip112 Removal of BioClip plug Combi Cutting unit modelsLubrication chart LubricationGeneral Lubricating wiresPedal mechanism in frame tunnel Chains in frame tunnel Engine oilGear lever TransmissionTriangular link Throttle and choke wires, lever bearingsDriver’s seat Belt tensioner Oil filter, replacementParking brake wire Transmission oil levelTrouble Shooting Schedule Problem ProcedureStorage ServiceWinter storage Wiring Diagram Technical Data Rider ProFlexRear ejector Combi Rear ejector BioClipEU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeAfter first 8 hours ServicejournalPre-delivery service Work doneHour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00