Husqvarna ProFlex 18 manual Removing the attachment frame, Dismantling the belt

Page 41

MAINTENANCE

Removing the attachment frame

Starting point for removing attachment frame:

•Cutting unit must be removed.

1.Release the catch so that the front mounting can be lifted clear of the cutting unit.

2.Slide the attachment frame backwards so that the tongue on the cutting unit is clear of the slot in the attachment frame, then lift off the frame.

Refit in reverse order.

8009-184

8009-185

Dismantling the belt

Starting point when dismantling the belt:

•No unit attached to the Rider.

•The front of the belt is hung around the hook guard’s handle.

The method of disengaging the front section of the belt from the front pulley is described in steps 5–8 under ”Removing the cutting unit”.

The entire belt is only dismantled as set out below, when the snow plough is fitted on the Rider.

1.Dismantle the steering plate under the support wheel. Use two 13 mm spanners.

2.Unhook the spring on the blade brake.

3.Pry off the belt from the intermediate pulley and remove the belt.

6016-114

8009-005

English – 39

Image 41

Contents English Rider ProFlexSvenska Contents Dear customer InstructionTravel and transport on public roads TowingSerial number Safety InstructionsGood service Read the instructions Explanation of SymbolsGeneral use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Never run the machine in an enclosed area TransportLocation of the controls PresentationPresentation Choke lever Throttle controlSpeed limiter Speed of the machine is steplessly regulatedLift lever for cutting unit Cutting unitParking brake Lever for adjustment of the cutting heightSeat FuellingStarting the engine DrivingBefore starting Driving the machine 6007-210 MAX Cutting tipsDisengage lever Stopping the engineYear MaintenanceMaintenance schedule Year 100 300 Hours Before afterEngine hood Dismantling of the machine hoodsNose Right-hand fenderCheck the transmission’s air intake Check the engine’s cooling air intakeLeft-hand fender Transmission coverChecking and adjustment of the steering wires Checking and adjusting the choke wire Checking and adjustment of the throttle wireAdjusting the hydrostatic wire Checking the tyre pressure Adjusting the brakesPoorly adjusted brakes can result in reduced braking power Replacing the air filter Checking of the fuel pump’s air filter Replacement of the fuel filterCleaning the pulse air filter Fitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Take care. Risk of crushing injury Fitting the cutting unitCheck that the belt is fitted around the tension roller Belt diagramWatch your fingers. Do not turn the blades or belt Cutting height ParallelismReplacing the break-pin BioClip Placing in the service position Service position for the cutting unitReleasing from the service position Checking the bladesDismantling the cutting unit 8009-169 Dismantling the belt Removing the attachment frameAssembling the belt Replacing the cutting unit’s belts Belt replacement on BioClipBelt replacement on BioClip112 Cutting unit models Removal of BioClip plug CombiLubrication Lubrication chartPedal mechanism in frame tunnel Lubricating wiresGeneral Engine oil Chains in frame tunnelTransmission Gear leverDriver’s seat Throttle and choke wires, lever bearingsTriangular link Parking brake wire Oil filter, replacementBelt tensioner Transmission oil levelProblem Procedure Trouble Shooting ScheduleWinter storage ServiceStorage Wiring Diagram Rider ProFlex Technical DataRear ejector BioClip Rear ejector CombiEU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityPre-delivery service ServicejournalAfter first 8 hours Work doneHour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00