Husqvarna ProFlex 18 manual Belt replacement on BioClip112

Page 44

MAINTENANCE

6.Version 2:

Assembly: First fit the lower belt and then the upper belt.

Ensure the blades are positioned as set out in the diagram, at 90 degrees to each other, otherwise the belts must be adjusted. When the blade bearings are loose the belts can be moved around to the next tooth.

Tighten the nuts enough so that the bearings rest against the cutting hood but still can be moved.

Tension the belt by turning the eccentric adjuster on top of the cutting hood. Tighten the nut.

Tighten all nuts on the blade bearings.

7.Version 2:

When the belt can be moved 7 mm inwards using a force of 10 N the belt is adjusted correctly.

8.Version 1 and 2:

Fit the cover over the belts and refit the parallel strut and attachment frame.

Belt replacement on BioClip112

The BioClip 112 has ”collision-proof” BioClip blades that are driven by a V-belt. To change the belt, see the instructions for the Cutting unit below.

Belt change on cutting unit with side or rear ejection and Combi unit

On these cutting units with ”collision-proof” blades, the blades are driven by one V-belt. Do as follows to change the V-belt:

1.Loosen the unit frame (1), the bolt on the parallelism arm (2) and the two bolts on the hood (3). Lift off the cutting unit’s hood.

2.Loosen the spring that tensions the V-belt and pry off the belt.

Reverse the procedure to fit the new belt.

6016-111

IMPORTANT INFORMATION

On BioClip 103 units the belts must be set at 90° to each other. In all other cases the blades can collide and cause serious damage to the cutting unit.

6012-079

3

3

1

2

6016-113

6012-080

42 – English

Image 44

Contents Rider ProFlex EnglishSvenska Contents Instruction Dear customerTravel and transport on public roads TowingSerial number Safety InstructionsGood service Explanation of Symbols Read the instructionsSafety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Never run the machine in an enclosed areaLocation of the controls PresentationPresentation Throttle control Choke leverSpeed limiter Speed of the machine is steplessly regulatedCutting unit Lift lever for cutting unitLever for adjustment of the cutting height Parking brakeSeat FuellingStarting the engine DrivingBefore starting Driving the machine 6007-210 Cutting tips MAXStopping the engine Disengage leverYear MaintenanceMaintenance schedule Hours Before after Year 100 300Dismantling of the machine hoods Engine hoodNose Right-hand fenderCheck the engine’s cooling air intake Check the transmission’s air intakeLeft-hand fender Transmission coverChecking and adjustment of the steering wires Checking and adjustment of the throttle wire Checking and adjusting the choke wireAdjusting the hydrostatic wire Checking the tyre pressure Adjusting the brakesPoorly adjusted brakes can result in reduced braking power Replacing the air filter Checking of the fuel pump’s air filter Replacement of the fuel filterCleaning the pulse air filter Fitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Fitting the cutting unit Take care. Risk of crushing injuryCheck that the belt is fitted around the tension roller Belt diagramWatch your fingers. Do not turn the blades or belt Parallelism Cutting heightReplacing the break-pin BioClip Service position for the cutting unit Placing in the service positionReleasing from the service position Checking the bladesDismantling the cutting unit 8009-169 Removing the attachment frame Dismantling the beltAssembling the belt Belt replacement on BioClip Replacing the cutting unit’s beltsBelt replacement on BioClip112 Removal of BioClip plug Combi Cutting unit modelsLubrication chart LubricationPedal mechanism in frame tunnel Lubricating wiresGeneral Chains in frame tunnel Engine oilGear lever TransmissionDriver’s seat Throttle and choke wires, lever bearingsTriangular link Oil filter, replacement Parking brake wireBelt tensioner Transmission oil levelTrouble Shooting Schedule Problem ProcedureWinter storage ServiceStorage Wiring Diagram Technical Data Rider ProFlexRear ejector Combi Rear ejector BioClipEU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeServicejournal Pre-delivery serviceAfter first 8 hours Work doneHour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00