Husqvarna ProFlex 18 Instruction, Dear customer, Travel and transport on public roads, Towing

Page 4

INSTRUCTION

Dear customer

Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a front- mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine.

We hope you will find this operator’s manual very useful. By following its instructions (on operation, service, maintenance, etc.) you will significantly extend the life of the machine and even its second-hand value.

When you sell your Rider, make sure you pass on the operator’s manual to the new owner. The last chapter in the operator’s manual consists of a Service Journal. Make sure that all service work and repairs are recorded. A well-documented service history reduces the costs of seasonal maintenance and influences the second-hand value of the machine. Remember to take along the operator’s manual when you take the Rider to the workshop for servicing.

Travel and transport on public roads

Check the relevant road traffic regulations before driving the machine on a public road. If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held.

Towing

If your machine has a hydrostatic transmission you should only tow it very short distances at low speed if absolutely necessary, otherwise the transmission may be damaged.

Intended use

This machine is designed solely for cutting grass on conventional lawns and other cleared and leveled ground without obstacles, as rocks, stumps etc., and, in conjunction with accessories supplied by the manufacturer even for other special tasks for which instructions are delivered with the accessory. Use in any other way is considered as contrary to the intended use. Compliance with and strict adherence to the conditions of operation, service and repair as specified by the manufacturer also constitute essential elements of the intended use.

This machine should be operated, serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations, all other generally recognised regulations on safety and occupational medicine, and all road traffic regulations must be observed at all times.

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting damage or injury

2 – English

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Rider ProFlex EnglishSvenska Contents Instruction Dear customerTravel and transport on public roads TowingGood service Safety InstructionsSerial number Explanation of Symbols Read the instructionsSafety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Never run the machine in an enclosed areaPresentation PresentationLocation of the controls Throttle control Choke leverSpeed limiter Speed of the machine is steplessly regulatedCutting unit Lift lever for cutting unitLever for adjustment of the cutting height Parking brakeSeat FuellingBefore starting DrivingStarting the engine Driving the machine 6007-210 Cutting tips MAXStopping the engine Disengage leverMaintenance schedule MaintenanceYear Hours Before after Year 100 300Dismantling of the machine hoods Engine hoodNose Right-hand fenderCheck the engine’s cooling air intake Check the transmission’s air intakeLeft-hand fender Transmission coverChecking and adjustment of the steering wires Checking and adjustment of the throttle wire Checking and adjusting the choke wireAdjusting the hydrostatic wire Poorly adjusted brakes can result in reduced braking power Adjusting the brakesChecking the tyre pressure Replacing the air filter Cleaning the pulse air filter Replacement of the fuel filterChecking of the fuel pump’s air filter Procedures on contact with acid Check the level of the battery acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Fitting the cutting unit Take care. Risk of crushing injuryWatch your fingers. Do not turn the blades or belt Belt diagramCheck that the belt is fitted around the tension roller Parallelism Cutting heightReplacing the break-pin BioClip Service position for the cutting unit Placing in the service positionReleasing from the service position Checking the bladesDismantling the cutting unit 8009-169 Removing the attachment frame Dismantling the beltAssembling the belt Belt replacement on BioClip Replacing the cutting unit’s beltsBelt replacement on BioClip112 Removal of BioClip plug Combi Cutting unit modelsLubrication chart LubricationGeneral Lubricating wiresPedal mechanism in frame tunnel Chains in frame tunnel Engine oilGear lever TransmissionTriangular link Throttle and choke wires, lever bearingsDriver’s seat Oil filter, replacement Parking brake wireBelt tensioner Transmission oil levelTrouble Shooting Schedule Problem ProcedureStorage ServiceWinter storage Wiring Diagram Technical Data Rider ProFlexRear ejector Combi Rear ejector BioClipEU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeServicejournal Pre-delivery serviceAfter first 8 hours Work doneHour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00
Top Page Image Contents