Husqvarna ProFlex 18 manual Gear lever, Transmission

Page 49

LUBRICATION

Check the engine oil level when the Rider is on level ground.

Raise the engine hood.

Take out the dipstick, wipe it clean and push it in again.

Do not screw in the dipstick.

Take out the dipstick again and read the oil level.

The oil level should be between the marks on the dipstick. If the level is close to the ”ADD” mark, top up with oil to the ”FULL” mark on the dipstick. Never fill above the ”FULL” mark.

Oil is added through the hole that the dipstick sits in.

Use SAE 30 or SAE 10W-30 grade engine oil, or 10W/40, class SC–SH (above 0° C/+32°F).

SAE 40 oil can be used above +20°C/+68°F.

Use SAE 5W-20 engine oil, class SC–SH (below 0° C/+32°F).

The engine holds 1.5 litres of oil, excluding the filter (1.7 litres including filter).

4. Gear lever

Remove the transmission cover by undoing the two screws.

Lubricate the joints and bearings on the left side using an oil can.

Push the rubber protector out of the way and lubricate the hydrostatic wire using an oil can. Press the pedal a few times and lubricate again.

Refit the rubber protector.

Refit the transmission cover.

5. Transmission

The oil should be changed by an authorised service workshop, and is described in the Workshop Ma- nual.

							8009-158
	ADD			FULL
ADD	FULL
							8009-159
	-20 C	-10 C	0 C	10 C	20 C	30 C	40 C
						SAE40

SAE30

SAE10W-30/SAE10W-40

SAE5W-20

-4 F 14 F 32 F 50 F 68 F 86 F 104 F

8009-140

6008-209

6020-024

English – 47

Image 49

Contents English Rider ProFlexSvenska Contents Dear customer InstructionTravel and transport on public roads TowingGood service Safety InstructionsSerial number Read the instructions Explanation of SymbolsGeneral use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Never run the machine in an enclosed area TransportPresentation PresentationLocation of the controls Choke lever Throttle controlSpeed limiter Speed of the machine is steplessly regulatedLift lever for cutting unit Cutting unitParking brake Lever for adjustment of the cutting heightSeat FuellingBefore starting DrivingStarting the engine Driving the machine 6007-210 MAX Cutting tipsDisengage lever Stopping the engineMaintenance schedule MaintenanceYear Year 100 300 Hours Before afterEngine hood Dismantling of the machine hoodsNose Right-hand fenderCheck the transmission’s air intake Check the engine’s cooling air intakeLeft-hand fender Transmission coverChecking and adjustment of the steering wires Checking and adjusting the choke wire Checking and adjustment of the throttle wireAdjusting the hydrostatic wire Poorly adjusted brakes can result in reduced braking power Adjusting the brakesChecking the tyre pressure Replacing the air filter Cleaning the pulse air filter Replacement of the fuel filterChecking of the fuel pump’s air filter Procedures on contact with acid Check the level of the battery acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Take care. Risk of crushing injury Fitting the cutting unitWatch your fingers. Do not turn the blades or belt Belt diagramCheck that the belt is fitted around the tension roller Cutting height ParallelismReplacing the break-pin BioClip Placing in the service position Service position for the cutting unitReleasing from the service position Checking the bladesDismantling the cutting unit 8009-169 Dismantling the belt Removing the attachment frameAssembling the belt Replacing the cutting unit’s belts Belt replacement on BioClipBelt replacement on BioClip112 Cutting unit models Removal of BioClip plug CombiLubrication Lubrication chartGeneral Lubricating wiresPedal mechanism in frame tunnel Engine oil Chains in frame tunnelTransmission Gear leverTriangular link Throttle and choke wires, lever bearingsDriver’s seat Parking brake wire Oil filter, replacementBelt tensioner Transmission oil levelProblem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage Wiring Diagram Rider ProFlex Technical DataRear ejector BioClip Rear ejector CombiEU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityPre-delivery service ServicejournalAfter first 8 hours Work doneHour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00