Husqvarna ProFlex 18 Triangular link, Driver’s seat, Throttle and choke wires, lever bearings

Page 50

LUBRICATION

6. Cutting unit Remove the nose cowling. Lubricate using an oil can:

A. Safety catch

- Joints and bearings Lubricate with grease:

B. Inner stud

C. Slot for attachment frame

6020-004

7. Triangular link

Grease nipple located behind the right side front wheel.

Lubricate with a grease gun until grease is squeezed out.

Use molybdenum sulphide grease.

8. Driver’s seat

Tip up the seat.

Lubricate the linkage of the scissor springs using an oil can; there are 8 lubrication points.

Lubricate the seat leg length adjustment mechanism using an oil can.

Lubricate the leg length adjustment rails using an oil can.

6008-233

8009-172

9. Throttle and choke wires, lever bearings

Remove the right side cover from the lever housing (3 screws) and open the engine hood. Lubricate the exposed ends of the wires using an oil can, including the ends at the engine. Move the levers through their full range of travel and lubricate again.

Lubricate joints, locks and bearings for the cutting deck control levers using an oil can.

6020-050

NOTE

Take care when fitting: The fine-threaded screw for the side cover must be fitted from the outside. Refit the side panel on the lever housing.

8009-157

48 – English

Image 50

Contents Rider ProFlex EnglishSvenska Contents Travel and transport on public roads InstructionDear customer TowingSerial number Safety InstructionsGood service Explanation of Symbols Read the instructionsSafety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Never run the machine in an enclosed areaLocation of the controls PresentationPresentation Speed limiter Throttle controlChoke lever Speed of the machine is steplessly regulatedCutting unit Lift lever for cutting unitSeat Lever for adjustment of the cutting heightParking brake FuellingStarting the engine DrivingBefore starting Driving the machine 6007-210 Cutting tips MAXStopping the engine Disengage leverYear MaintenanceMaintenance schedule Hours Before after Year 100 300Nose Dismantling of the machine hoodsEngine hood Right-hand fenderLeft-hand fender Check the engine’s cooling air intakeCheck the transmission’s air intake Transmission coverChecking and adjustment of the steering wires Checking and adjustment of the throttle wire Checking and adjusting the choke wireAdjusting the hydrostatic wire Checking the tyre pressure Adjusting the brakesPoorly adjusted brakes can result in reduced braking power Replacing the air filter Checking of the fuel pump’s air filter Replacement of the fuel filterCleaning the pulse air filter Fitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Fitting the cutting unit Take care. Risk of crushing injuryCheck that the belt is fitted around the tension roller Belt diagramWatch your fingers. Do not turn the blades or belt Parallelism Cutting heightReplacing the break-pin BioClip Releasing from the service position Service position for the cutting unitPlacing in the service position Checking the bladesDismantling the cutting unit 8009-169 Removing the attachment frame Dismantling the beltAssembling the belt Belt replacement on BioClip Replacing the cutting unit’s beltsBelt replacement on BioClip112 Removal of BioClip plug Combi Cutting unit modelsLubrication chart LubricationPedal mechanism in frame tunnel Lubricating wiresGeneral Chains in frame tunnel Engine oilGear lever TransmissionDriver’s seat Throttle and choke wires, lever bearingsTriangular link Belt tensioner Oil filter, replacementParking brake wire Transmission oil levelTrouble Shooting Schedule Problem ProcedureWinter storage ServiceStorage Wiring Diagram Technical Data Rider ProFlexRear ejector Combi Rear ejector BioClipEU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeAfter first 8 hours ServicejournalPre-delivery service Work doneHour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00