Husqvarna ProFlex 18 manual Do not smoke when carrying out maintenance

Page 11

SAFETY INSTRUCTIONS

If leaks arise in the fuel system, the engine must not be started until the problem has been resolved.

Store the machine and fuel in such a way that there is no risk that leaking fuel or fumes can cause any damage.

Check the fuel level before each use and leave space for the fuel to expand, because the heat from the engine and the sun may otherwise cause the fuel to expand and overflow.

Avoid overfilling. If you spill petrol on the machine, wipe up the spill and wait until it has evaporated before starting the engine. If you spill petrol on your clothing, change your clothing.

Allow the machine to cool before performing any actions in the engine compartment.

Be especially careful when handling battery acid. Acid on the skin can cause serious corrosive injuries. In the event of spillage on the skin wash immediately with water.

Acid in the eyes can cause blindness, contact a doctor immediately.

Take care with battery maintenance. Explosive gases form in the battery. Never perform maintenance on the battery while smoking or in the vicinity of open flames or sparks. This can cause the battery to explode and cause serious injuries.

Make sure all nuts and bolts are tightened correctly and that the equipment is in good condition.

Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven if protective plates, protective covers, safety switches or other protective devices are not fitted or are defective.

Do not change the setting of governors and avoid running the engine at excessively high revs. If you run too fast, you risk damaging the machine components.

WARNING!

The engine and the exhaust system become very hot during operation.

Risk of burn injuries if touched.

WARNING!

The battery contains lead and lead pollutants, chemicals that are considered to cause cancer, birth defects or other repro- ductive impairment. Wash your hands after touching the battery.

8009-242

Do not smoke when carrying out maintenance.

English – 9

Image 11
Contents English Rider ProFlexSvenska Contents Towing InstructionDear customer Travel and transport on public roadsSerial number Safety InstructionsGood service Read the instructions Explanation of SymbolsGeneral use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Never run the machine in an enclosed area TransportLocation of the controls PresentationPresentation Speed of the machine is steplessly regulated Throttle controlChoke lever Speed limiterLift lever for cutting unit Cutting unitFuelling Lever for adjustment of the cutting heightParking brake SeatStarting the engine DrivingBefore starting Driving the machine 6007-210 MAX Cutting tipsDisengage lever Stopping the engineYear MaintenanceMaintenance schedule Year 100 300 Hours Before afterRight-hand fender Dismantling of the machine hoodsEngine hood NoseTransmission cover Check the engine’s cooling air intakeCheck the transmission’s air intake Left-hand fenderChecking and adjustment of the steering wires Checking and adjusting the choke wire Checking and adjustment of the throttle wireAdjusting the hydrostatic wire Checking the tyre pressure Adjusting the brakesPoorly adjusted brakes can result in reduced braking power Replacing the air filter Checking of the fuel pump’s air filter Replacement of the fuel filterCleaning the pulse air filter Fitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Take care. Risk of crushing injury Fitting the cutting unitCheck that the belt is fitted around the tension roller Belt diagramWatch your fingers. Do not turn the blades or belt Cutting height ParallelismReplacing the break-pin BioClip Checking the blades Service position for the cutting unitPlacing in the service position Releasing from the service positionDismantling the cutting unit 8009-169 Dismantling the belt Removing the attachment frameAssembling the belt Replacing the cutting unit’s belts Belt replacement on BioClipBelt replacement on BioClip112 Cutting unit models Removal of BioClip plug CombiLubrication Lubrication chartPedal mechanism in frame tunnel Lubricating wiresGeneral Engine oil Chains in frame tunnelTransmission Gear leverDriver’s seat Throttle and choke wires, lever bearingsTriangular link Transmission oil level Oil filter, replacementParking brake wire Belt tensionerProblem Procedure Trouble Shooting ScheduleWinter storage ServiceStorage Wiring Diagram Rider ProFlex Technical DataRear ejector BioClip Rear ejector CombiEU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityWork done ServicejournalPre-delivery service After first 8 hoursHour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´+H%,¶6c¨ English 114 00