Husqvarna P 525D, P 520D manual Presentation

Page 12

PRESENTATION

Presentation

Congratulations on your choice of an excellent quality product that will give you great pleasure for many years. This operator’s manual describes P 520D and P 525D.

P 520D and P 525D are equipped with hydraulic steering and an equipment hoist.

The machines are equipped with four wheel drive.

The power transmission from the engine is handled by a hydrostatic transmission, which allows variable variation of the speed by using the pedals. One pedal for driving forward and one for reverse.

Throttle trigger

The throttle control regulates the engine speed, and thereby also the rotation speed of the blades.

To increase or reduce the engine speed the control is moved forwards or backwards.

When driving the throttle control must be in the position for maximum engine speed, work mode.

Speed limiter

The speed of the machine is steplessly regulated with two pedals. Pedal (1) is used to drive forwards, and pedal (2) to drive backwards.

1

2

WARNING! Make sure that branches do not

!obstruct the pedals when mowing under bushes. Otherwise there is a risk you may lose control.

Counter

The chronometer shows how many hours the engine has been running.

Any time when the engine is not running but the ignition is switched on is not registered.The last digit shows tenths of an hour (6 minutes).

Parking brake

Operate the parking brake by moving the handle forwards.

Cutting unit

P 520D and P 525D can be equipped with two different cutting units.

•Combi 132

•Combi 155

The Combi-unit, equipped with a BioClip-plug, ﬁnely chops the cuttings to fertiliser. Without the BioClip-plug the unit works in the same way as a rear ejection unit.The rear ejector ejects the clippings behind the unit without ﬁnely chopping them.

12 – English

Image 12

Contents 520D 525D EnglishContents Pre-delivery service After the ﬁrst 25 hoursIntroduction Dear CustomerDriving and transport on public roads TowingGood service KEY to Symbols SymbolsWhat is WHAT? Location of the controlsSafety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Adjusting the cutting height Lever for hydraulic lift of attachmentsLifting the Cutting Unit Transport Position Lowering the Unit Mowing PositionLights and power outlet Safety instructionsSeat FuelingInstrument panel Bypass valvesRops Roll Over Protective Structure Auxiliary lift systemStarting and driving when cold Starting EngineBefore starting Start the engineStarting the engine with a weak battery Connecting the jump leadsRemove the cables in the reverse order Driving Driving the RiderBraking Stop the engineCutting tips Other objects which can be thrown out by the bladesMaintenance schedule 800Starting Completed Cleaning Removing of the machine hoodsChecking the engine’s cooling air intake Adjustment of pump and alternator belt Adjusting the parking brakeReplacement of fuel ﬁlter Change pump and alternator beltCleaning the air ﬁlter Cleaning the engine and mufﬂerCleaning the ﬁlter cover Replacing the air ﬁlterCheck the safety system Replacing the light bulbsMain fuse Checking the tyre pressureCheck the battery Cutting Unit ComponentsFitting the cutting head Pins are loosened. Observe caution to avoid Removing the cutting unitLift arms move with great force when Trapping your handService position for the cutting unit Placing in the service positionCutting height and tilt angle adjustment Restoring from service positionCutting height Replacing the cutting unit belts Checking the bladesRemoving the BioClip plug Tilt angleAdjustment of PTO belts Change PTO beltsChange coolant Glycol Water Freezing pointLubrication schedule GeneralAccessories Pivot wheel bearingsCutting unit bevel gear Universal drive shaft jointsDrive shaft front support bearing Drive shaft rear support bearingSteering cylinder Joint bearingChanging the oil ﬁlter Check the hydraulic system oil levelReplacing the engine oil Drained directly after stopping the engineKnobs for setting the cutting height Lubricate the parking brake wireDriver seat Lubricating the cablesProblem Procedure Engine does not start Engine seems to have no powerStarter motor does not turn over the engine Engine does not run smoothlyBattery does not charge Engine overheatsUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Service Winter storageGuard Technical Data EC-declaration of conformity Applies to Europe only Sound levels see noteVibration levels see note 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨ Original instructions