Husqvarna P 520D, P 525D manual What is WHAT?, Location of the controls

Page 7

WHAT IS WHAT?


	12 11 10		9	8	7 6	5	4 3 2		1
13	14	15	16		17 18	19	20	21		22	23	24	25

Location of the controls

1	Knob for seatback angle	14	Counter
2	Throttle trigger	15	Temperature gauge
3	Power outlet	16	Knob for adjustment of the seat suspension
4	Switch for the power outlet	17	Lever for longitudinal seat adjustment
5	Control for cutting unit drive	18	Bypass valve front axle
6	Lever for hydraulic lift of attachments	19	Product and serial number plate
7	Parking brake	20	Fuel gauge
8	Switch for the lights	21	Catch for lowering seat
9	Ignition lock	22	Fuel cap
10	Instrument panel	23	Knob for lumbar support
11	Speed limiter for reversing	24	Cover lock
12	Speed limiter for driving forward	25	Bypass valve rear axle
13	Adjusting the cutting height

English – 7

Image 7

Contents English 520D 525DContents After the ﬁrst 25 hours Pre-delivery serviceTowing IntroductionDear Customer Driving and transport on public roadsGood service Symbols KEY to SymbolsLocation of the controls What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Lowering the Unit Mowing Position Adjusting the cutting heightLever for hydraulic lift of attachments Lifting the Cutting Unit Transport PositionFueling Lights and power outletSafety instructions SeatBypass valves Instrument panelAuxiliary lift system Rops Roll Over Protective StructureStart the engine Starting and driving when coldStarting Engine Before startingConnecting the jump leads Starting the engine with a weak batteryRemove the cables in the reverse order Stop the engine DrivingDriving the Rider BrakingOther objects which can be thrown out by the blades Cutting tips800 Maintenance scheduleStarting Completed Removing of the machine hoods CleaningChecking the engine’s cooling air intake Change pump and alternator belt Adjustment of pump and alternator beltAdjusting the parking brake Replacement of fuel ﬁlterReplacing the air ﬁlter Cleaning the air ﬁlterCleaning the engine and mufﬂer Cleaning the ﬁlter coverChecking the tyre pressure Check the safety systemReplacing the light bulbs Main fuseCutting Unit Components Check the batteryFitting the cutting head Trapping your hand Pins are loosened. Observe caution to avoidRemoving the cutting unit Lift arms move with great force whenPlacing in the service position Service position for the cutting unitRestoring from service position Cutting height and tilt angle adjustmentCutting height Tilt angle Replacing the cutting unit beltsChecking the blades Removing the BioClip plugChange PTO belts Adjustment of PTO beltsGlycol Water Freezing point Change coolantGeneral Lubrication scheduleUniversal drive shaft joints AccessoriesPivot wheel bearings Cutting unit bevel gearJoint bearing Drive shaft front support bearingDrive shaft rear support bearing Steering cylinderDrained directly after stopping the engine Changing the oil ﬁlterCheck the hydraulic system oil level Replacing the engine oilLubricating the cables Knobs for setting the cutting heightLubricate the parking brake wire Driver seatEngine does not run smoothly Problem Procedure Engine does not startEngine seems to have no power Starter motor does not turn over the engineEngine overheats Battery does not chargeUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Winter storage ServiceGuard Technical Data Sound levels see note EC-declaration of conformity Applies to Europe onlyVibration levels see note Original instructions 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨