Husqvarna P 520D, P 525D manual Maintenance schedule, 800, Starting Completed

Page 21

Maintenance

Maintenance schedule

The following is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised service workshop.

Maintenance	Daily maintenance		Maintenance interval in hours

	Before	After work is	10	40	100	200	400	800
	starting	completed	10	40	100	200	400	800
	starting	completed

Check the safety system	X

Check for fuel and oil leakage.	O

Check the engine’s oil level	X		X

Check coolant level and antifreeze.	X		X

Checking the transmission oil level	X		X

Check and clean the engine’s cooling air intake, clean the radiator.		X	X

Cleaning		X

Start engine and blades, listen for noise		O

Check nuts and screws		O

Clean underside of cutting unit		X

Lubricate throttle cable				X

Grease the blade shafts				X

Check air ﬁlter			X

Check the tyre pressures.			X

Lubricate according to lubrication schedule, see under heading				X	X
"LUBRICATION"				X	X
"LUBRICATION"

Clean thoroughly around engine				X

Clean thoroughly around transmission				X

Clean the air ﬁlter and empty the particle collector				X

Checking the blades				X

Replace the fuel ﬁlter					X

Change engine oil and ﬁlter1)					X1)
Check the synchronisation between the front and rear wheels.					O

Change hydraulic oil and hydraulic ﬁlter.							O

Check belt tension and condition (alternator belt, PTO belt, cutting					X
unit belt)					X
unit belt)

Check the battery condition, clean as necessary.				X

Clean transmission air intake	X		X

Check oil level in the bevel gear, top up if necessary.						X

Check the wheel nuts.						O

Check the parking brake						X

Replace the air ﬁlter2).						X2)
Change belts (PTO belt and cutting unit belt).							X

Change the oil in the bevel gear.							X

Change pump and alternator belt								X

Change coolant (50% glycol).							X

Service at an authorised service representative.					O

1)First change after 25 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours. 2) Maintenance and replacement are required more often in dusty conditions.

X = Described in this operator's manual

O = Not described in this operator's manual

WARNING! No service procedures must be

!conducted on the engine or cutting unit unless:

The engine is switched off. The parking brake is applied. The ignition key is removed. The cutting unit is disengaged.

English – 21

Image 21

Contents English 520D 525DContents After the ﬁrst 25 hours Pre-delivery serviceDear Customer IntroductionDriving and transport on public roads TowingGood service Symbols KEY to SymbolsLocation of the controls What is WHAT?Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Lever for hydraulic lift of attachments Adjusting the cutting heightLifting the Cutting Unit Transport Position Lowering the Unit Mowing PositionSafety instructions Lights and power outletSeat FuelingBypass valves Instrument panelAuxiliary lift system Rops Roll Over Protective StructureStarting Engine Starting and driving when coldBefore starting Start the engine Starting the engine with a weak battery Connecting the jump leads Remove the cables in the reverse order Driving the Rider DrivingBraking Stop the engineOther objects which can be thrown out by the blades Cutting tipsMaintenance schedule 800Starting Completed Cleaning Removing of the machine hoodsChecking the engine’s cooling air intake Adjusting the parking brake Adjustment of pump and alternator beltReplacement of fuel ﬁlter Change pump and alternator beltCleaning the engine and mufﬂer Cleaning the air ﬁlterCleaning the ﬁlter cover Replacing the air ﬁlterReplacing the light bulbs Check the safety systemMain fuse Checking the tyre pressureCheck the battery Cutting Unit ComponentsFitting the cutting head Removing the cutting unit Pins are loosened. Observe caution to avoidLift arms move with great force when Trapping your handPlacing in the service position Service position for the cutting unitCutting height and tilt angle adjustment Restoring from service positionCutting height Checking the blades Replacing the cutting unit beltsRemoving the BioClip plug Tilt angleChange PTO belts Adjustment of PTO beltsGlycol Water Freezing point Change coolantGeneral Lubrication schedulePivot wheel bearings AccessoriesCutting unit bevel gear Universal drive shaft jointsDrive shaft rear support bearing Drive shaft front support bearingSteering cylinder Joint bearingCheck the hydraulic system oil level Changing the oil ﬁlterReplacing the engine oil Drained directly after stopping the engineLubricate the parking brake wire Knobs for setting the cutting heightDriver seat Lubricating the cablesEngine seems to have no power Problem Procedure Engine does not startStarter motor does not turn over the engine Engine does not run smoothlyBattery does not charge Engine overheatsUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Service Winter storageGuard Technical Data EC-declaration of conformity Applies to Europe only Sound levels see noteVibration levels see note Original instructions 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨