Husqvarna P 525D Accessories, Pivot wheel bearings, Cutting unit bevel gear, Cutting unit bracket

Page 34

Lubrication

Accessories

Lubrication or other maintenance of optional equipment or accessories is not described in this manual. This equipment too, naturally, requires maintenance. See the manuals for the respective accessories for instructions.

Pivot wheel bearings

4 nipples (sprocket and pivot shaft bearing), lubricate with grease gun until grease appears.

The cutting unit bevel gear

A sight glass is located in the plug on the front of the bevel gear.

•Check the level when the cutting unit is in the down position.

•When ﬁlling, raise the cutting unit to the transport position and remove the plug with the sight glass. Fill with gear oil SAE 80W/90.

Changing the oil

•Empty the bevel gear through the sight glass using a pump ﬁtted with a plastic tube that extends to the bottom of the housing.

•Alternative: Remove the cutting unit and plastic covers. Place the cutting unit on its edge and empty the bevel gear through the plug.

•Fill the bevel gear with 0.4 litres of gear oil SAE 80W/90

Universal drive shaft joints

•Remove the service hatch.

•Loosen the two quick connectors on the universal drive shaft and remove the universal drive shaft.

•The universal drive shaft has two grease nipples, one on the front hub and one on the rear hub. Lubricate with a grease gun until the grease is forced out.

•Lubricate the telescopic joint of the universal drive shaft with grease.

Cutting unit bracket

Lubricate swivel joints and shafts with oil.

Lift arm rear bearings

•Remove the service hatch.

•2 grease nipples, one on each side. Lubricate with a grease gun until the grease is forced out.

Lift cylinder

•Remove the service hatch.

•2 grease nipples, one on each side. Lubricate with a grease gun until the grease is forced out.

34 – English

Image 34

Contents 520D 525D EnglishContents Pre-delivery service After the ﬁrst 25 hoursDriving and transport on public roads IntroductionDear Customer TowingGood service KEY to Symbols SymbolsWhat is WHAT? Location of the controlsInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Lifting the Cutting Unit Transport Position Adjusting the cutting heightLever for hydraulic lift of attachments Lowering the Unit Mowing PositionSeat Lights and power outletSafety instructions FuelingInstrument panel Bypass valvesRops Roll Over Protective Structure Auxiliary lift systemBefore starting Starting and driving when coldStarting Engine Start the engineConnecting the jump leads Starting the engine with a weak batteryRemove the cables in the reverse order Braking DrivingDriving the Rider Stop the engineCutting tips Other objects which can be thrown out by the blades800 Maintenance scheduleStarting Completed Removing of the machine hoods CleaningChecking the engine’s cooling air intake Replacement of fuel ﬁlter Adjustment of pump and alternator beltAdjusting the parking brake Change pump and alternator beltCleaning the ﬁlter cover Cleaning the air ﬁlterCleaning the engine and mufﬂer Replacing the air ﬁlterMain fuse Check the safety systemReplacing the light bulbs Checking the tyre pressureCutting Unit Components Check the batteryFitting the cutting head Lift arms move with great force when Pins are loosened. Observe caution to avoidRemoving the cutting unit Trapping your handService position for the cutting unit Placing in the service positionRestoring from service position Cutting height and tilt angle adjustmentCutting height Removing the BioClip plug Replacing the cutting unit beltsChecking the blades Tilt angleAdjustment of PTO belts Change PTO beltsChange coolant Glycol Water Freezing pointLubrication schedule GeneralCutting unit bevel gear AccessoriesPivot wheel bearings Universal drive shaft jointsSteering cylinder Drive shaft front support bearingDrive shaft rear support bearing Joint bearingReplacing the engine oil Changing the oil ﬁlterCheck the hydraulic system oil level Drained directly after stopping the engineDriver seat Knobs for setting the cutting heightLubricate the parking brake wire Lubricating the cablesStarter motor does not turn over the engine Problem Procedure Engine does not startEngine seems to have no power Engine does not run smoothlyEngine overheats Battery does not chargeUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Winter storage ServiceGuard Technical Data Sound levels see note EC-declaration of conformity Applies to Europe onlyVibration levels see note 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨ Original instructions